6-24
port hybrid protocol-vlan
Syntax
port hybrid protocol-vlan
vlan
vlan-id
{
protocol-index
[
to
protocol-end
] |
all
}
undo
port hybrid protocol-vlan
{
vlan
vlan-id
{
protocol-index
[
to
protocol-end
] |
all
} |
all
}
View
Ethernet interface view, port group view, Layer-2 aggregate interface view
Default Level
2: System level
Parameters
vlan
vlan
-
id
: Specifies a VLAN ID, in the range 1 to 4094.
protocol-index
: Protocol index, ranging from 0 to 15, specified by the users or assigned by the system
automatically when the protocol-based VLAN is created. You can use the
display protocol-vlan vlan
all
command to display the protocol indexes.
to
protocol-end
: Specifies the end protocol index, ranging from 0 to 15. The
protocol-end
argument
must be greater than or equal to the beginning protocol index.
all
: Specifies all protocols bound with
vlan-id
.
Description
Use the
port hybrid protocol-vlan vlan
command to associate the hybrid port(s) with a
protocol-based VLAN.
Use the
undo
port hybrid protocol-vlan
command to remove the association.
z
In port group view, this command applies to all ports in the port group. For information about port
groups, refer to
Ethernet Interface Configuration
in the
Access Volume
.
z
In Layer-2 aggregate interface view, this command applies to the Layer-2 aggregate interface and
all its member ports. After you perform the configuration, the system starts applying the
configuration to the aggregate interface and its aggregation member ports. If the system fails to do
that on the aggregate interface, it stops applying the configuration to the aggregation member
ports. If it fails to do that on an aggregation member port, it simply skips the port and moves to the
next port. For information about Layer-2 aggregate interfaces, refer to
Link Aggregation
Configuration
in the
Access Volume
.
Before issuing this command, make sure that you have made the following configurations:
z
Create a VLAN and associate it with specified protocols.
z
Configure the link type as hybrid.
z
Configure the port to allow the protocol-based VLAN to pass through.
Related commands:
display protocol-vlan interface
.
Examples
# Associate the hybrid port GigabitEthernet 1/0/1 with protocol 0 (IPv4) in VLAN 2.
<Sysname> system-view
[Sysname] vlan 2
[Sysname-vlan2] protocol-vlan ipv4
Содержание E4510-48G
