background image

 

 

About this Manual 

 
We’ve added this manual to the Agilent website in an effort to help you support 
your product.  This manual is the best copy we could find; it may be incomplete 
or contain dated information.  If we find a more recent copy in the future, we will 
add it to the Agilent website. 
 
 

Support for Your Product 

 
Agilent no longer sells or supports this product.  Our service centers may be able 
to perform calibration if no repair parts are needed, but no other support from 
Agilent is available.  You will find any other available product information on the 
Agilent Test & Measurement website, 

www.tm.agilent.com

.

 

 
 
 

HP References in this Manual 
 

This manual may contain references to HP or Hewlett-Packard.  Please note that 
Hewlett-Packard's former test and measurement, semiconductor products and 
chemical analysis businesses are now part of Agilent Technologies.  We have 
made no changes to this manual copy.  In other documentation, to reduce 
potential confusion, the only change to product numbers and names has been in 
the company name prefix: where a product number/name was HP XXXX the 
current name/number is now Agilent XXXX.  For example, model number 
HP8648A is now model number Agilent 8648A. 
 
 

 

Содержание E2492A


































Отзывы: