manualshive.com logo in svg

HP E1399A, Руководство пользователя

Поделиться
Скачать
HP E1399A Скачать руководство пользователя страница 35

User Access Points

The breadboard module contains traces (stubs) for accessing many of the
signal lines on backplane connector P1. Table 2-13 shows the signal lines
that are brought onto the module but not implemented. They are available as
signal access points for your custom circuits.

Table 2-14 shows all of the implemented signal lines available as access
points, either as inputs from the backplane to your own custom circuitry, or
as outputs to the backplane from your custom circuits.

Table 2-13. User Access Points (Stubs)

Signal Lines

Description

ACFAIL*
BERR*
SERCLK
SERDAT*

AC Input Power failure
Bus ERRor signal
Synchronizes data transmission on the VMSbus
Used for VMSbus data transmission

Table 2-14. User Access Points (Implemented Signals)

A1-A5
BASE+0
BASE+2
BASE+4
BASE+6
BASE+8
BASE+A
BASE+C
BASE+E
CR2-CR7
DB0-DB15
DS0 & DS1
SR0, SR1
SR2
SR3
SR4-SR7
DBEN*
CRESET*
DTACK
DTACK INH
AS
SYSFAIL
SYSFAIL INH
HRESET*
IRQ
LATCH*
PIACK*
CADDR

Backplane address lines A1-A5 (latched)
ID Register Enable line
Device Type Register Enable line
Status and Control Registers Enable line
User-assignable Enable line
User-assignable Enable line
User-assignable Enable line
User-assignable Enable line
User-assignable Enable line
Control Register output lines
Breadboard Module internal Data Bus lines
Buffered data strobes
Status Register (pulled up)
Status Register (pulled up)
Status Register (pulled up)
Status Register (pulled up)
Data bus buffer enable
Card RESET, software (CRO) or hardware (SYSRESET*)
Data Transfer ACKnowledge (DTACK high = DTACK* low)
DTACK INHibit
Buffered address strobe
Card failure signal (jumpered to GND)
SYSFAIL INHibit (jumpered to GND)
Hardware RESET (from SYSRESET*)
Interrupt ReQuest line, User-implemented jumper to ground
Latches data into write registers
Peripheral Interrupt ACKnowledge line
Card ADDRess match

Chapter 2

Configuring the HP E1399A  35

Содержание E1399A



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды