HP Dual Roll Kit Скачать руководство пользователя страница 11

Страница: 11 / 15

Open the latches at both ends of the spindle (if they were closed) and push the roll on its spindle

into the printer.

10.

Close the latches to secure the spindle in place.

TIP:

If you cannot close the gear side latch, try sliding the spindle towards the side plate to make

sure the end flange is not sitting on the bearings.

11.

In the same way, load the spindle with the empty cores into the front of the printer. In this case, the

geared end of the spindle should be on the right.

12.

Check that the printer has finished raising the carriage beam.

13.

Pass the leading edges of both rolls through the printer to the output spindle.

TIP:

LX850/LX820 only:

Use the Media Loading Tool to load both rolls through the media

path at the same time.

ENWW

Load rolls into the printer

Dual-r

oll spindle

Содержание Dual Roll Kit
















Результаты поиска

Содержание Dual Roll Kit

Отзывы:

Похожие инструкции для Dual Roll Kit

Бренды по названию

Популярные бренды

HP Dual Roll Kit, Руководство пользователя

Результаты поиска

Содержание Dual Roll Kit

Отзывы:

Похожие инструкции для Dual Roll Kit

Бренды по названию

Популярные бренды