HP Compaq dx7200 MT Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 216

HP Compaq dx7200 MT Скачать руководство пользователя страница 32

3–2

390812-001

Service Reference Guide, dx7200

Desktop Management

3.1.1 Altiris Deployment Solution Agent

This program is pre-loaded on the computer. When installed, it enables communication with the
administrator Deployment Solution console.

To install Altiris Deployment Solution Agent:

1. Click

Start

.

2. Click

All Programs

.

3. Click

Software Setup

.

4. Click

Next

.

5. Scroll down and click on the link to install Altiris AClient.

3.1.2 HP Local Recovery

Local Recovery backs-up data and system files to a protected area on the hard drive. If data or
files are lost, deleted, or corrupted, Local Recovery can be used to retrieve data or restore the last
good system image.

To install this pre-loaded program:

1. Click

Start

.

2. Click

Local Recovery

.

3. Click

Next

.

4. Scroll down and click on the link to install HP Local Recovery.

3.2 Remote System Installation

Remote System Installation allows you to start and set up your system using the software and
configuration information located on a network server by initiating the Preboot Execution
Environment (PXE). The Remote System Installation feature is usually used as a system setup
and configuration tool, and can be used for the following tasks:

■

Formatting a hard drive.

■

Deploying a software image on one or more new PCs.

■

Remotely updating the system BIOS in flash ROM. See

Section 3.4.1, “Remote ROM

■

Configuring the system BIOS settings.

To initiate Remote System Installation, press

F12

when the F12 = Network Service Boot

message appears in the lower-right corner of the HP logo screen. Follow the instructions on the
screen to continue the process. The default boot order is a BIOS configuration setting that can be
changed to always attempt to PXE boot.

HP and Altiris have partnered to provide tools designed to make the task of corporate PC
deployment and management easier and less time-consuming, ultimately lowering the total cost
of ownership and making HP PCs the most manageable client PCs in the enterprise environment.

«
...
30
31
32
33
34
...
»

Содержание Compaq dx7200 MT

























































































































































































































Отзывы:

Нет отзывов