HP Compaq dx7200 MT Скачать руководство пользователя страница 129

Страница: 129 / 216

Service Reference Guide, dx7200

390812-001

7–21

Removal and Replacement Procedures— Slim Tower (ST) Chassis

8. Press the green drive retention latch

located on the side of the diskette drive to disengage

the drive from the drive cage and slide the diskette drive forward approximately 6mm
(1/4 inch)

9. Lift the rear of the drive up so that the rear guide screws clear the top of the drive cage

As the drive rises it automatically slides forward until it is free from the drive cage

To replace the drive, reverse the removal procedure making sure you rotate the rear of the drive
down, pivoting on the front screws.

✎

When replacing the drive, transfer the four metric screws from the old drive to the new one. The
screws take the place of drive rails.

Содержание Compaq dx7200 MT

























































































































































































































Результаты поиска

Содержание Compaq dx7200 MT

Отзывы:

HP Compaq dx7200 MT, Справочное руководство, Страница: 129 / 216

Результаты поиска

Содержание Compaq dx7200 MT

Отзывы: