HP Compaq dc7600 SFF Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 73

background image

Hardware Reference Guide

www.hp.com

2-15

Hardware Upgrades

8. Install the expansion card by sliding the card under the slot cover

retention latch then pressing the card down into the slot on the
system board.

✎

Be sure not to scrape other components in the chassis when installing
an expansion card.

Installing an Expansion Card

9. Rotate the slot cover retention latch back in place to secure the

expansion card.

10. Connect external cables to the installed card, if needed. Connect

internal cables to the system board, if needed. If the card requires
audio, connect the audio cable to the connector on the system
board labeled “Aux” (located towards the edge of the system
board under the power supply cage).

11. Replace the computer cover.

12. Plug in the power cord and and turn on the computer.

13. If you normally lock the Smart Cover Lock, use Computer Setup

to relock the lock and enable the Smart Cover Sensor.

«
...
23
24
25
26
27
...
»

Содержание Compaq dc7600 SFF










































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq dc7600 SFF

Бренд: IBM Страницы: 164

6219 - IntelliStation M - Pro

Бренд: IBM Страницы: 154

Бренд: IBM Страницы: 72

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 90

Бренд: NEC Страницы: 146

Бренд: Igel Страницы: 2

Бренд: Lobo Drives Страницы: 40

Бренд: HP Страницы: 33

280 G5 SFF Business PC

Бренд: HP Страницы: 19

2133 Mini-Note PC

Бренд: HP Страницы: 4

Бренд: HP Страницы: 16

205 G2 AiO Business

Бренд: HP Страницы: 13

Бренд: HP Страницы: 60

Бренд: HP Страницы: 13

Бренд: HP Страницы: 6

Бренд: HP Страницы: 7

280 G3 Microtower Business

Бренд: HP Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды