HP Compaq dc7600 SFF Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 73

background image

Hardware Reference Guide

www.hp.com

2-13

Hardware Upgrades

Installing an Expansion Card

The computer has two standard PCI expansion slots that can
accommodate an expansion card up to 17.46 cm (6.875 inches)
in length. The computer also has one PCI Express x1 expansion slot
and one PCI Express x16 expansion slot.

✎

The PCI and PCI Express slots support only low profile cards unless
an optional riser is installed. The optional riser supports two full
height standard PCI slots. If the riser is installed, the PCI Express x16
expansion slot is inaccessible.

Expansion Slot Locations

✎

You can install a PCI Express x1, x4, x8, or x16 expansion card in the
PCI Express x16 expansion slot.

Item

Description

1

PCI expansion slot

2

PCI expansion slot

3

PCI Express x16 expansion slot

4

PCI Express x1 expansion slot

«
...
21
22
23
24
25
...
»

Содержание Compaq dc7600 SFF










































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq dc7600 SFF

Бренд: T-MAG Страницы: 22

Бренд: DATA FROM SKY Страницы: 40

Deep Silence 6 Revision B

Бренд: Nanoxia Страницы: 24

TORO WORKSTATION JBTORO15WS

Бренд: J.Burrows Страницы: 8

Бренд: ARE Страницы: 39

Бренд: Cartft Страницы: 10

Бренд: INTERACT Страницы: 15

Бренд: Compaq Страницы: 110

Бренд: Oceanic Страницы: 80

DEC 3000 Model 400S AXP

Бренд: Digital Equipment Страницы: 13

Бренд: Onyx Страницы: 42

ZBOX PRO QK5P1000

Бренд: Zotac Страницы: 57

Бренд: Zotac Страницы: 1

VAIO VGN-AR850E

Бренд: Sony Страницы: 2

VAIO VGN-AR840E

Бренд: Sony Страницы: 2

VAIO VGN-AR825E

Бренд: Sony Страницы: 2

VAIO VGN-AR810E

Бренд: Sony Страницы: 2

VAIO VGN-AR790U/B

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды