HP Compaq d538 CMT Скачать руководство пользователя

Страница: 39 / 80

Hardware Reference Guide

www.hp.com

2–21

Hardware Upgrades

✎

If you are installing a third optional drive in the bottom 5.25-inch
drive bay, you must also install an expansion card with an IDE
controller and data cable (not supplied) because the secondary IDE
controller supports only two drives.

6. Connect the drive power

and signal

cables and, if it is an

optical drive and if analog audio is preferred to digital audio,
connect the audio cable

. The other end of the audio cable

should be connected to the embedded audio connector on the
system board.

Connecting the Drive Cables

7. Remove the appropriate bezel blank from the subpanel inside the

front bezel. See the

“Removing Bezel Blanks”

section for more

information.

8. Replace the computer access panel and front bezel.

9. If you normally lock the Smart Cover Lock, use Computer Setup

to relock the lock and enable the Smart Cover Sensor.

10. Reconfigure the computer, if necessary. Refer to the Computer

Setup (F10) Utility Guide on the Documentation Library CD for
instructions about using Computer Setup.

Содержание Compaq d538 CMT

















































































Результаты поиска

Содержание Compaq d538 CMT

Отзывы:

Похожие инструкции для Compaq d538 CMT

Бренды по названию

Популярные бренды

HP Compaq d538 CMT, Справочник по аппаратуре

Результаты поиска

Содержание Compaq d538 CMT

Отзывы:

Похожие инструкции для Compaq d538 CMT

Бренды по названию

Популярные бренды