HP C-Series Скачать руководство пользователя

Страница: 5 / 24

Configure...

Fabric parameters (yes, y, no, n): [no]

Domain: (1..239) [97]

[Select the domain ID in the range 97-127, if change is required]

BB credit: (1..27) [16]

R_A_TOV: (4000..120000) [10000]

[Ensure this value is 10000 for all switches in the fabric]

E_D_TOV: (1000..5000) [2000]

[Ensure this value is 2000 for all switches in the fabric]

WAN_TOV: (1000..120000) [0]

Data field size: (256..2112) [2112]

Sequence Level Switching: (0..1) [0]

Disable Device Probing: (0..1) [0]

Suppress Class F Traffic: (0..1) [0]

SYNC IO mode: (0..1) [0]

VC Encoded Address Mode: (0..1) [0]

Core Switch PID Format: (0..1) [1]

Per-frame Route Priority: (0..1) [0]

Long Distance Fabric: (0..1) [0]

Virtual Channel parameters (yes, y, no, n): [no]

Zoning Operation parameters (yes, y, no, n): [no]

RSCN Transmission Mode (yes, y, no, n): [no]

Arbitrated Loop parameters (yes, y, no, n): [no]

System services (yes, y, no, n): [no]

Portlog events enable (yes, y, no, n): [no]

No changes.

Switch:admin>

Step 3: Disable management server

Platform management services must be disabled fabric-wide before enabling the interopmode and
merging the fabrics. The

msPlMgmtDeactivate

command deactivates the Platform Database

Management Service of each switch in the fabric:

Switch:admin>

msPlMgmtDeactivate

This will erase all Platform entries. Are you sure? (yes, y, no, n): [no]

Committing configuration...done.

Request Fabric to Deactivate Platform Management services....

Done.

Switch:admin>

NOTE:

You must reboot the switch after executing the

msPlMgmtDeactivate

command. However, you

can avoid multiple reboots by delaying the switch reboot until after completing the next step (4).

Step 4: Verify and configure fabric operating mode

For B-series switches the

interopmode 1

must be enabled before merging with C-series switches.

This command enables interopmode on individual switches only and therefore, must be executed on
each B-series switch in the fabric. Use the following Telnet command to change the operating mode:

admin

Password:

xxxxxxxx

Switch:admin>

switchDisable

Switch:admin> 0x101a8dd0 (tThad): Jan 20 10:47:55

WARNING FW-STATUS_SWITCH, 3, Switch status changed from HEALTHY/OK to Marginal/Warning

Switch:admin>

Fabric interoperability: Merging fabrics based on C-series and B-series Fibre Channel switches applic-

ation notes

Содержание C-Series

























Результаты поиска

Содержание C-Series

Отзывы:

Похожие инструкции для C-Series

Бренды по названию

Популярные бренды

HP C-Series, Руководство по совместимости

Результаты поиска

Содержание C-Series

Отзывы:

Похожие инструкции для C-Series

Бренды по названию

Популярные бренды