HP C-Series Скачать руководство пользователя

Страница: 13 / 24

MDS9509(config-zone)#

member pwwn 21:00:00:20:37:28:31:6d

MDS9509(config-zone)#

member pwwn 21:00:00:20:37:28:24:7b

MDS9509(config-zone)#

member pwwn 21:00:00:20:37:28:22:ea

MDS9509(config-zone)#

member pwwn 21:00:00:20:37:28:2e:65

MDS9509(config-zone)#

member pwwn 21:00:00:20:37:28:26:0d

MDS9509(config-zone)#

exit

MDS9509(config)#

zoneset name mdscore vsan 1

MDS9509(config-zoneset)#

member vz1

MDS9509(config-zoneset)#

member vz2

MDS9509(config-zoneset)#

member vz3

MDS9509(config-zoneset)#

exit

MDS9509(config)#

At this point three zones have been created; vz1, vz2, and vz3; as well as a zoneset titled

MDSCORE

To activate the

MDSCORE

zoneset:

MDS9509(config)#

zoneset activate name mdscore vsan 1

Zoneset Activation initiated. check zone status

MDS9509(config)#

exit

View each switch in the fabric to verify the newly-defined zoning is in place:

MDS9509#

show zoneset active

zoneset name mdscore vsan 1

zone name vz1 vsan 1

* fcid 0x630500 [pwwn 50:06:01:60:88:02:90:cb]

* fcid 0x610400 [pwwn 10:00:00:00:c9:24:3d:90]

zone name vz2 vsan 1

* fcid 0x630400 [pwwn 10:00:00:00:c9:24:3f:75]

* fcid 0x6514e2 [pwwn 21:00:00:20:37:a7:ca:b7]

* fcid 0x6514e4 [pwwn 21:00:00:20:37:a7:c7:e0]

* fcid 0x6514e8 [pwwn 21:00:00:20:37:a7:c7:df]

zone name vz3 vsan 1

* fcid 0x651500 [pwwn 10:00:00:e0:69:f0:43:9f]

* fcid 0x6105dc [pwwn 21:00:00:20:37:28:31:6d]

* fcid 0x6105e0 [pwwn 21:00:00:20:37:28:24:7b]

* fcid 0x6105e1 [pwwn 21:00:00:20:37:28:22:ea]

* fcid 0x6105e2 [pwwn 21:00:00:20:37:28:2e:65]

* fcid 0x6105e4 [pwwn 21:00:00:20:37:28:26:0d]

zone name $default_zone$ vsan 1

You can view the same information from other C-series switches that are connected in the same fabric.

B-series switches

Use Telnet on B-series switches to verify that the zoning information has propagated properly. On
B-series you will see the active configuration as well as any defined configurations that are not part
of active configuration.

Use the

configshow

command to verify the configuration:

Fabric interoperability: Merging fabrics based on C-series and B-series Fibre Channel switches applic-

ation notes

Содержание C-Series

























Результаты поиска

Содержание C-Series

Отзывы:

Похожие инструкции для C-Series

Бренды по названию

Популярные бренды

HP C-Series, Руководство по совместимости

Результаты поиска

Содержание C-Series

Отзывы:

Похожие инструкции для C-Series

Бренды по названию

Популярные бренды