background image

Preface-iii

Printing History

The manual printing date and part number indicate its current edition. The printing date
will change when a new edition is printed. Minor changes may be made at reprint without
changing the printing date.

Manual updates may be issued between editions to correct errors or document product
changes. To ensure that you receive the updated or new editions, you should subscribe to
the appropriate product support service. See your HP sales representative for details.

First Edition: ......................................................................... September, 1997

NOTE

Reader Comments. We welcome your comments about our documentation.
If you have editorial suggestions or recommended improvements for this
document, please write to us. You can reach us through e-mail at:
[email protected] or by sending your letter to: Documentation
Manager M/S 5657, Hewlett-Packard Company, 8000 Foothills Blvd.,
Roseville, CA 95747-6588 USA.
 Please include the following information in
your message:

• Title of the manual you are referencing.

• Manual part number (from the title page).

• Edition number or publication date (from the title page).

• Your name.

• Your company’s name.

SERIOUS ERRORS, such as technical inaccuracies that may render a
program or a hardware device inoperative, should be reported to your HP
Response Center or directly to a Support Engineer.

Preface

This edition of the Mounting Kit Installation Guide contains technical information about
attaching the rack mount hardware to the D Class family of computers. The procedures in
this guide are intended for trained and experienced HP field service personnel. At the time
of publication, this family of computers included the following models:

HP 9000 Model:

D2xx

D3xx

Содержание A3764-90003













Отзывы: