HP 9000 Model D280 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 68

background image

1- 27

D Class System Memory Upgrade

Memory Upgrade Verification Procedure

D. Halt the Boot
Process

If Autoboot is set to ON, you will have to interrupt the boot process to get to the
Boot Console Handler, where you will have access to the commands for verifying
the memory installation.When prompted by the following message, halt the boot
process by pressing any key on the keyboard

Processor is booting from first available device.

To discontinue, press any key within 10 seconds.

Boot terminated.

-- Main Menu -------------------------------------------------

Command Description
----------- ---------------------
BOot [PRI|ALT|<path>]           Boot from specified path
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>]   Search for boot devices
TOC                             Soft boot the system

COnfiguration [<command>]

Access Configuration menu/commands

INformation [<command>]

Access Information menu/commands

SERvice [<command>]

Access Service menu/commands

DIsplay

Redisplay the current menu

HElp [<menu>|<command>]

Display help for menu or command

RESET

Restart the system

-------
Main Menu: Enter command >

«
...
31
32
33
34
35
...
»

Содержание 9000 Model D280





































































Отзывы:

Нет отзывов

Похожие инструкции для 9000 Model D280

Бренд: Commodore Страницы: 23

Бренд: Apricot Страницы: 139

Бренд: Alienware Страницы: 20

Бренд: Lenovo Страницы: 26

Бренд: Lenovo Страницы: 4

Бренд: Lenovo Страницы: 2

Бренд: Lenovo Страницы: 41

Бренд: Lenovo Страницы: 45

41U3074 - Laser Mouse

Бренд: Lenovo Страницы: 42

53581FU - IdeaCentre K220 Desktop

Бренд: Lenovo Страницы: 64

Бренд: Lenovo Страницы: 78

Бренд: Lenovo Страницы: 174

Бренд: Lenovo Страницы: 82

6072A5U - ThinkCentre M57 - 6072

Бренд: Lenovo Страницы: 506

Бренд: Lenovo Страницы: 4

Бренд: Acnodes Страницы: 10

Бренд: Moxa Technologies Страницы: 6

Бренд: Penpower Technology Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды