manualshive.com logo in svg

HP 8970B, Руководство по обслуживанию, Страница: 13 / 40

Поделиться
Скачать
HP 8970B Скачать руководство пользователя страница 13

HP 8970B Option 020 Service Manual Supplement

1-5

Block Diagram and Parts List

Material List

Material List

1.  Replaces 08970-60097 from prefix break 3811.
2.  This is the same part number as the main instrument but different wires are used. The wires

that are not used are tied back.

3.  These replace 08970-80051/52
4.  Replaces 08970-60003
5.  Replaces 08970-60034

Table 1-1:  HP 8970B Option 020 Material List - main differences for Option 020

Description

Part Number

Quantity

2.05 GHz Low Pass Filter

0955-0634

1

Semi-rigid cable W1

08970-20082

1

Input Assembly

08970-60097

1

Input Assembly

08970-60125

1

1

2 to 8 GHz YIG Tuned Oscillator

0955-0630

1

YIG Tuned Oscillator Interface Board

08970-60045

1

YIG Tuned Oscillator Shield

08590-00047

1

Semi-rigid cable W2

08970-20081

1

Semi-rigid cable W3

08970-20083

1

Semi-rigid cable W4

08970-20085

1

Microwave Mixer

0955-0635

1

Semi-rigid cable W5

08970-20084

1

Microwave Isolator

0960-0638

1

Right Angle SMA(F) to SMA (M) Adapter W6

1250-1249

1

4.5 GHz Low Pass Filter

9135-0169

1

SMA(M) to SMA (M) Adapter W7

1250-2189

1

Second Convertor

5086-7909

1

600 MHz SAW Oscillator

08970-60093

1

Flexi Cable W8

83711-60035

1

Flexi Cable W9

83711-60035

1

Main Wiring Harness

08970-60046

2

1

Firmware EPROM’s

08970-80071/72

3

2

20 MHz IF Assembly

08970-60050

4

1

Driver Board Assembly

08970-60089

5

1

SMA (M) 50

Ω

 Termination

0960-0053

1

Содержание 8970B









































Отзывы:

Нет отзывов