HP 8920A Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 658

background image

132

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

The CALL CONTROL Screen

NOTE:

When the CALL CONTROL screen is displayed, the Test Set’s instrumentation is configured
for optimal performance of the signaling decoder. It is recommended that FM deviation
measurements be made using either the ANALOG MEAS screen. Using the CALL
CONTROL screen to make FM deviation measurements may result in slightly degraded
results.

Handoff

This field is used to initiate a handoff from the current voice channel assignments
to a new set of voice channel assignments. The voice channel number to hand the
mobile station off to, the channel location (NAMPS system type only), the initial
power level to use on the new voice channel, the DSAT sequence (NAMPS
system type only) to transpond on the mobile station, and the SAT tone frequency
to transpond on the new voice channel are specified using the

Chan:

,

Ch Loc:

,

Pwr Lvl:

,

DSAT:

, and

SAT:

fields in the

Voice Channel Assignment

section of the CALL CONTROL screen.

MS Id

This field is used to enter the identification number of the mobile station. The

MS Id

has two fields. The upper field is a one-of-many selection field and is used

to select the format for entering the identification number. The lower field is a
numeric entry field and is used to enter the identification number in the format
selected using the upper field. The contents of the lower field are automatically
updated upon successful completion of a mobile station registration.

There are two formats which can be used to enter the identification number. The
identification number can be entered as either the 10-digit phone number in
decimal (for example, 5095551212) or as the mobile identification number (MIN)
in hexadecimal (for example, AAABBBBBB). The first 3 characters (AAA) in the
field represent MIN2 and the last 6 characters (BBBBBB) represent MIN1.

To enter the identification number, select upper field and select the desired format
(

Phone Num

or

MIN2 MIN1

). Then select the lower field and enter the

information in the selected format. If the desired format is already selected then
simply select the lower field and enter the information in the selected format. The
formats are coupled, that is, if the

Phone Num

format is selected and the 10-digit

phone number is entered, the

MIN2 MIN1

information is automatically updated,

and vice versa.

«
...
130
131
132
133
134
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Odom Страницы: 19

Бренд: MacDon Страницы: 30

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: Quadro mdb Страницы: 4

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

Бренд: Daga Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды