HP 8920A Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 658

background image

127

Chapter 6, Call Processing Subsystem

The CALL CONTROL Screen

Display

This field is used to select the type of mobile station information to be displayed
in the upper right-hand portion of the CALL CONTROL screen:

•

Select

Data

to display information received from the mobile station on the reverse

control channel or reverse voice channel. If the data message(s) received from the
mobile station can be correctly decoded, the decoded message contents are displayed.
If the data messages cannot be correctly decoded, the raw data message bits are
displayed in hexadecimal format.

Figure 19 on page 128

shows the layout of the CALL

CONTROL screen when a decoding error has occurred.

The decoded order confirmation message, origination message, and order message are
available from the reverse control channel. The following pieces of information are dis-
played when these messages are properly decoded: phone number, ESN (dec), ESN (hex),
the decoded Station Class Mark (SCM), and the called number. The decoded SCM con-
sists of: the mobile station power class (Class I, II, or III), the transmission type (continu-
ous/discontinuous), and the transmission bandwidth (20 MHz or 25 MHz).

•

The decoded Order Confirmation Message is available from the reverse voice chan-
nel.

•

Select

Meas

to display modulation quality measurements made on the mobile station’s

RF carrier while on a voice channel.
•

and

For system types

AMPS

,

TACS

,

JTACS

, and wide channel

NAMPS

four characteristics

of the RF carrier are measured: TX Freq Error, TX Power, FM Deviation, and AF Fre-
quency. When set to the

Meas

display, the AF Analyzer’s settings are 300 Hz HPF, 15

kHz LPF, De-Emphasis Off, PK+ detector. The

Meas

information is available only when

the Test Set’s

Connect

annunciator is lit (connect state). Refer to the individual field

descriptions for further information.

Figure 20 on page 129

shows the layout of the

CALL CONTROL screen when

Meas

is selected.

For system type

NAMPS

with

Ch Loc:

set to Lower, Middle, or Upper, four characteris-

tics of the RF carrier are measured: TX Freq Error, TX Power, FM Deviation, and DSAT/
DST. When set to

NMeas

display, the AF Analyzer’s settings are: 300 Hz HPF, 15 kHz

LPF, De-Emphasis 750

µ

s, PK+ detector. The

NMeas

information is available only when

the Test Set’s

Connect

annunciator is lit (connect state). Refer to the individual field

descriptions for further information.

Figure 21 on page 130

shows the layout of the

NAMPS CALL CONTROL screen when

NMeas

is selected.

«
...
125
126
127
128
129
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Haag-Streit Страницы: 16

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: Labnet Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: Napoleon Страницы: 3

Бренд: Daikin Страницы: 52

Бренд: Tieline Страницы: 359

GP1313 Schaukel Premium 2.2

Бренд: gartenpirat Страницы: 4

Бренд: PARAMOUNT BED Страницы: 120

TRICEPS EXTENSION

Бренд: ETENON Fitness Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды