HP 652A Скачать руководство пользователя

Страница: 32 / 78

Model 652A

b. Set 652A FREQUENCY RANGE switch to XIM and

FREQUENCY dial to 1 0. If 652A does not oscillate, adjust
A2C5, S I CS and S I C I O .

c . Adjust A2C5 and S I C S alternately for 10.1 5 MHz

( 1 .5% high) as indicated on counter and for required

voltage on A2TP2 (within ± 0.02 V of reference voltage

recorded in Paragraph 5-30, Step

fl. If the required

frequency and A2TP2 voltage cannot be obtained, change

the setting ofS1CIO and repeat this step.

d. Set FREQUENCY dial to 5 and note frequency ; if

not within tolerance (Table 5-1), perform the following:

1 . Set dial to 1 0 and slightly change setting of

S I CI O . (Example: If frequency is low with 5 set
on dial, adjust 81 CI 0 to slightly lower frequency

when dial is at 1 0 ; and vice versa.)

2. Readjust A2C5 and SI C5 alternately for

1 0. 1 5 MHz and required A2TP2 voltage (same as

Step c).

3 . Set dial to 5 and note frequency; if still not

within tolerance, repeat Steps d-I , d-2, and d-3 as

often as necessary until tolerances are met at both

5 and 10 positions of FREQUENCY dial. If

necessary, change the value of S l CI 4 *.

e. Set FREQUENCY dial to 1 . Check that frequency

(Table 5-

and A2TP2 voltage (same as in Step c) are

within required tolerances; if either is not correct, change
value of RANGE switch resistors (Table 5-6) simultane

ously until both frequency and voltage are within required
limits. If RANGE switch resistors are changed, it will be

necessary to repeat Steps c and d.

Set FREQUENCY dial to 2; counter should indicate

2000 ± 60 kHz.

NOTE

It may b e necessary

set frequency about 1%

high for the dial to track.

g. While monitoring the voltage at A2TP2, move the

dial through its range from 1 to 10; the A2TP2 voltage

must remain within the range: - 300 m V to - 450 m V. If

A2TP2 voltage exceeds these limits, then recalibrate using

Paragraph 5-33.

5-34. X 1 00K Range Frequency Calibration.

NOTE

The following adjustments are critical. For

each adjustment, remove cover and make the

adjustment; then replace cover before making

frequency or voltage checks. If desired, Figure

5-10 gives a scaled drawing of top and bottom

Section V

alignment access covers with cut-outs lhat will

allow adjustments while the covers are in

place. The dimensions are given in inches.

a. Connect equipment as shown in Figure 5-8.

b. Set FREQUENCY RANGE to X 1 00K and FRE

QUENCY dial to 10. Adjust S I C4 and S I C9 simultaneously

for 1 MHz (See Table 5-1) as indicated on counter and for

required A2TP2 voltage (within ± 0.02 V of reference
voltage recorded in Paragraph 5-30, Step fl.

c. Set FREQUENCY dial to 1 . Counter should indicate

100 kHz (See Table 5-7) and A2TP2 voltage should be the

same as in Step b ; if either is not within tolerance, change

value of RANGE switch resistors (Table 5- 6) simultane
ously until both frequency and voltage are within required
limits.

d. Repeat Step b.

e. Set FREQUENCY dial to 5 ; frequency should be

500 kHz (See Table 5-7) as indicated on counter and

A2TP2 voltage should be wi thin 40 m V of reference
voltage. If either is incorrect, repeat Steps b , c, and d until

both frequency and A2TP2 voltage are within tolerance.

(Remove test lead attached to A2TP2.)

5-35. 1 0 MHz F latness Adjustment.

a. Connect 652A to ac voltmeter as shown in Figure

5-2.

b. Set 652A controls as follows:

FREQUENCY RANGE . . . . . . . . . . . . . . Xl K

FREQUENCY dial

. . . . . . . . . . . . . . . . . . 1 0

OUTPUT ATTENUATOR . . . . . . . . . . 3.0 V
OUTPUT MONITOR . . . . . . . .

.NORMAL

c. Adjust 652A OUTPUT AMPLITUDE and VERNIER

controls for 3.0 V rms as indicated on ac voltmeter. Do not
readjust AMPLITUDE controls for remainder of this

paragraph.

d. Connect equipment as shown in Figure 5-3. Adjust

reference supply for null indication. Do not readjust
reference supply once null is obtained.

NOTE

Instrument covers must be in place.

e. Set 652A FREQUENCY RANGE to XIM. Sweep

FREQUENCY dial slowly from I to 1 0. Null meter

deviation from null should not exceed ± 0.54 mY.

f. Adjust A2Cl4 to reduce any output peaking. If

necessary, change value of A2C24- slightly.

5-1 3

Содержание 652A















































































Результаты поиска

Содержание 652A

Отзывы:

Похожие инструкции для 652A

Бренды по названию

Популярные бренды

HP 652A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 652A

Отзывы:

Похожие инструкции для 652A

Бренды по названию

Популярные бренды