HP 520 5/XX Скачать руководство пользователя страница 98

Страница: 98 / 146

4 Summary of the HP/Phoenix BIOS

HP/Phoenix BIOS (BIOS version: GX.07.xx)

Message

Corrective Action and/or Explanation

Operating system not found

Check whether the disk, HDD, FDD or CD-ROM disk drive is

connected.
If it is connected, check that it is detected by

Setup.

Check that your boot device is enabled on the

Setup

Security menu.
If the problem persists, check that the boot device contains
the operating system.

Missing operating system

If you have configured HDD user parameters, check that

they are correct. Otherwise, use HDD type “Auto”
parameters.

Failure fixed disk
(preceded by a 30” time-out)

Check that HDD is connected.
Check that HDD is detected in

Setup

Check that boot on hard disk drive is enabled in

Setup

Diskette Drive A (or B) error

Check whether the diskette drive is connected. Check

Setup

for the configuration.

System battery is dead

You may get this message if the PC is disconnected for a
few days. When you Power-on the PC, run

Setup

to update

the configuration information. The message should no
longer be displayed. Should the problem persist, replace the
battery.

Keyboard error

Check that the keyboard is connected.

Resource Allocation Conflict -PCI
device 0079 on motherboard

Clear CMOS.

Video Plug and Play interrupted or
failed Re-enable in Setup and try again

You may have powered your PC Off/On too quickly and the
PC turned off Video plug and play as a protection.

System CMOS checksum bad - run
Setup

CMOS contents have changed between 2 power-on
sessions. Run

Setup

for configuration.

I/O device IRQ conflict

Serial ports A and B may have been assigned the same IRQ.
Assign a different IRQ to each serial port and save the
configuration.

No message, system “hangs” after
POST

Check that cache memory and main memory are correctly
set in their sockets.

Other

An error message may be displayed and the PC may “hang”
for 20 seconds and then beep. The POST is probably
checking for a mass storage device which it cannot find and
the PC is in Timeout Mode. After Timeout, run

Setup

check the configuration.

Содержание 520 5/XX



















































































































































Результаты поиска

Содержание 520 5/XX

Отзывы:

Похожие инструкции для 520 5/XX

Бренды по названию

Популярные бренды

HP 520 5/XX, Техническое справочное руководство

Результаты поиска

Содержание 520 5/XX

Отзывы:

Похожие инструкции для 520 5/XX

Бренды по названию

Популярные бренды