HP 10Gb Ethernet BL-c Скачать руководство пользователя страница 157

Страница: 157 / 228

Configuration Menu 157

Table 127

Hot Links Master Menu options

Command Description

cur

Displays the current Master interface configuration.

Hot Links Backup configuration

Command:

/cfg/l2/hotlink/trigger <

1-4

>/backup

[Backup Menu]

port - Set port in Backup

trunk - Set trunk in Backup

cur - Display current Backup configuration

The following table describes the Hot Links Backup Menu options.

Table 128

Hot Links Backup menu options

Command Description

port

<port number (0, 18-21)>

Adds the selected port to the Backup interface.

Enter zero (0) to clear the port.

trunk

<trunk group number (1-12)>

Adds the selected trunk group to the Backup interface.

cur

Displays the current Backup interface configuration.

Содержание 10Gb Ethernet BL-c





































































































































































































































Результаты поиска

Содержание 10Gb Ethernet BL-c

Отзывы:

Похожие инструкции для 10Gb Ethernet BL-c

Бренды по названию

Популярные бренды

HP 10Gb Ethernet BL-c, Справочник по командам

Результаты поиска

Содержание 10Gb Ethernet BL-c

Отзывы:

Похожие инструкции для 10Gb Ethernet BL-c

Бренды по названию

Популярные бренды