background image

24632-0-0508

Page 41

TROUBLESHOOTING

PROBLEM

CAUSES

SOLUTION

Pilot flame does not light

A)  Gas supply valve closed

B)  Air in gas pipes

C)  Valve does not work properly

A)  Open gas supply valve

B)  Repeat ignition procedure

C)  Place knob on PILOT position and 

depress fully

When ignition knob is released, pilot 

extinguishes

A)  Air remains in gas pipes

B)  Dirty pilot

C)  Thermocouple is defective

A)  Repeat ignition procedure

B)  Clean pilot

C)  Check with Service Department

Burner burns abnormally

A)  Gas supply valve is not fully open

B)  Flame lifts when appliance is cold

A)  Open gas supply valve fully

B)  Keep on MIN. for about 10 minutes

Burner shuts down while in operation

A)  Gas supply interrupted

B)  Incorrect piping connection

A)  Gas supply re-established

B)  Connect piping according to installa-

tion instructions

Burner burns with yellow flames

A)  Incorrect piping connection

A)  Connect piping according to installa-

tion instructions

Difficulties in heating room

A)  Incorrect heater size

B)  Low gas pressure

C)  Partially plugged injector

A)  Contact Service Department for sizing 

room

B)  Check with Service Department

C)  Check with Service Department

To order parts, please visit our website at www.housewarmerproducts.com or call 877-459-1583.
All parts listed in the 

Parts List

 have a 

Part Number

. When ordering parts, first obtain the 

Model Number

 from the name plate on your 

equipment. Then determine the 

Part Number (not the Index Number) and the Description 

of each part from the following appropriate 

illustration and list. Be sure to give all this information.
Furnace Model Number 

    Part Description 

Furnace Serial Number  

  Part Number 

Type of Gas (Propane or Natural) 
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. 
Shipments contingent upon strikes, fires and all causes beyond our control.

Empire Comfort Systems, Inc.  Nine Eighteen Freeburg Ave.   Belleville, IL  62222-0529

HOW TO ORDER REPAIR PARTS

Содержание HWDV080BDV(N,P)-1

















































Отзывы: