HouseWarmer HWDV080BDV(N,P)-1 Скачать руководство пользователя страница 15

Страница: 15 / 48

24632-0-0508

Page 15

Note: All references must be considered as if the observer is standing in front of the wall and/or appliance.

HEATER TO

BACK CASING

MOUNTING

SCREWS

WALL

MOUNTING TAB

WALL

MOUNTING

SCREWS

WALL MOUNTING

PLATE

Mark the venting system hole location (as indicated on page

18) and the six holes through the wall mounting plate. Drill

accordingly. Insert the four wall anchors provided and tighten

the wall mounting plate ﬁrmly. Use special anchor fasteners if

the heater is to be installed on a wooden (hollow) wall. Line

up the two (2) tabs on the top of the wall mounting plate with

the holes in the back of the unit. Slide the back of the unit onto

the tabs of the wall mounting plate. Secure the back of the unit

into place using two (2) screws. Replace casing door. The heater

is now ready to receive the venting system assembly from the

opposite side of the wall.

Note: All references must be considered as if the observer is

standing in front of the wall and/or appliance.

IMPORTANT: The venting system must be properly

installed to insure proper and safe operation. The venting

system must also be properly re-installed and re-sealed to

insure proper and safe operation.

INSTALLATION AND ASSEMBLY

WARNING: Any change to this heater or its control can be dangerous. Provide adequate clearances and

accessibility for purposes of servicing and proper operation.

A manufactured home (USA only) installation must conform with the Manufactured Home Construction and Safety Standard, Title 24

CFR, Part 3280 or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI Z225.1.

Due to high surface temperature, keep children, clothing, and furniture away. Keep burner and control compartments clean.

INSTALLATION OVERVIEW

WARNING: Improper installation, adjustments, alteration, service, or maintenance can cause property damage, personal injury

or loss of life.

Installation and service must be performed by a qualiﬁed installer, service agency, or the gas supplier.

These wall furnace models are designed for direct venting through a wall. Only venting components approved for these furnaces may

be used.
This unit is to be installed on a wall from 4 1/2" to 12" (114.3 mm to 304.8 mm) thick.

Содержание HWDV080BDV(N,P)-1

















































Результаты поиска

Содержание HWDV080BDV(N,P)-1

Отзывы:

Похожие инструкции для HWDV080BDV(N,P)-1

Бренды по названию

Популярные бренды

HouseWarmer HWDV080BDV(N,P)-1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание HWDV080BDV(N,P)-1

Отзывы:

Похожие инструкции для HWDV080BDV(N,P)-1

Бренды по названию

Популярные бренды