Hotsy 560SS Скачать руководство пользователя страница 1

Страница: 1 / 16

8.914-357.0

SERIAL

NUMBER:

DATE

PURCHASED:

FOR SALES AND SERVICE, PLEASE CONTACT:

SPECIFICATIONS

●

Pump Volume At Pump Head: 2.3 GPM/138 GPH

●

Pump Pressure At Pump Head: 1500 PSI

●

Burner Type: Fuel Oil Fired, 214,300 BTU/Hr.

●

Burner Fuel Pressure: 150 PSI

●

Machine Voltage: 115VAC/60Hz/1Ph

●

Total Machine Amperage: 20 Amps

●

Machine Weight: 310 Lbs.

●

Shipping Weight: 370 Lbs.

●

Exhaust Stack Size: 8"

●

Machine Dimensions: Length = 42", Width = 30", Height = 49"

Output specifi cations are based on engine power curves at 100 meters
above sea level and 25

C ambient temperature in accordance with

SAE J1349.

LISTED

MODEL 560SS

Read instructions carefully before attempting to assemble, install, operate or service this pressure
washer. Failure to comply with instructions could result in personal injury and/or property damage!

OPERATING INSTRUCTIONS

AND PARTS MANUAL

Содержание 560SS

















Результаты поиска

Содержание 560SS

Отзывы:

Похожие инструкции для 560SS

Бренды по названию

Популярные бренды

Hotsy 560SS, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 560SS

Отзывы:

Похожие инструкции для 560SS

Бренды по названию

Популярные бренды