Hotsy 560SS Скачать руководство пользователя страница 6

Страница: 6 / 16

8.914-357.0 • HOTSY 560SS • Rev. 03/11

OPERA

OR’S MANU

PRESSURE W

ASHER

COMPONENT IDENTIFICATION

OFF

F°

10-

02033

200

165

130

235

270

300

TEMPERA

TURE

BURNER

RESET

PUMP

OFF

Pump

— Delivers a specifi c gpm to the high pressure

nozzle which develops pressure.

Spray Gun

— Controls the application of water and

detergent onto cleaning surface with trigger device.
Includes safety latch.

Detergent Injector

— Allows you to siphon and mix

detergents.

Wand

— Must be connected to the spray gun.

High Pressure Hose

— Connect one end to water

pump high pressure discharge nipple and the other
end to spray gun.

Unloader Valve

— Safety device which, when the

spray gun closes, prevents over pressurization.

Relief Valve

- Safety device wich when working pressue

rises due to an abnormal condition relieves system
pressure preventing equipment damage.

Note

If trigger on spray gun is released for more

than 2 minutes, water will leak from the pump
protector. Warm water will discharge from pump
protector onto fl oor. This system prevents internal
pump damage.

Wand

High

Pressure

Hose

Spray Gun

Detergent

Injector

Unloader

Valve

Pump

GFCI

Relief valve

Exhaust Vent

Control

Box

Motor

Hose Reel

Mount

Содержание 560SS

















Результаты поиска

Содержание 560SS

Отзывы:

Похожие инструкции для 560SS

Бренды по названию

Популярные бренды

Hotsy 560SS, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 560SS

Отзывы:

Похожие инструкции для 560SS

Бренды по названию

Популярные бренды