background image

GB

2

Installation

A

 

Keep this instruction manual in a safe place for

future reference. If  the  appliance is sold,  given

away  or  moved,  please  ensure  the  manual  remains

with the machine so that the new owner may

benefit  from  the  advice  contained  within  it.

  Please  read  this  instruction  manual  carefully  it

contains  important  information  regarding  the  safe

installation,  use  and  maintenance  of  the  appliance.

 You will find the guarantee and other details relating to

the installation process in the bag containing this booklet.

Unpacking  and  levelling

Unpacking

1. Once the washing machine has been removed from

the packaging, check that it has not been damaged

during  transportation.

If it has been damaged, contact the retailer and do

not proceed any further with the installation process.

2. Remove the four

transit bolts and the

rubber bush with the

respective  spacer,

situated on the rear of

the  appliance.

NB:

The  plastic  spacers

may fall down inside the

machine once the bolt

has been removed, and

will not interfere with the operation of the machine.

3. Having removed the 4 bolts use the 4 plastic

blanking plates to cover the 4 holes.

4. Keep all the pieces; if the washing machine is

transported  in  future,  the  transit  bolts  and

spacers will have to be replaced in order to avoid

damaging the inside of the machine.

 Packaging materials should not be used as toys by

children.

Levelling

1. Position the washing machine on a level and sturdy

floor,  without  resting  it  against  walls  or  cabinets.

2. If the floor is uneven,

the feet of the

appliance  may  be

adjusted  until  it  reaches

a  perfectly  horizontal

position (the angle of

inclination  must  not

exceed  2  degrees).

 If the appliance is levelled correctly it will be more

stable and much less likely to cause vibrations and

noise during the spin cycle.

 If positioned on a fitted carpet or a rug, adjust the

feet in such a way as to allow room for air to circulate

and provide ventilation beneath the washing machine.

Connecting  the  cold  water  and

electricity  supplies

Connecting  the  water  inlet  hose

Before connecting the inlet hose to the cold water supply,

allow the water to flow from the tap until it runs clear.

1. Connect the inlet hose

to the machine, by

screwing it into the cold

water inlet on the upper

right hand side of the

back of the machine

(see  figure)

.

2. Place the seal A

(provided in the bag) on

the end of the inlet hose

and screw it to a cold

water tap with a 3/4 BSP

threaded  connection

(see  figure)

.

3. Make sure there are no kinks or bends in the inlet

hose.

 

The water pressure at the tap must fall within the

values indicated in the Technical data table 

(see

next page).

 If the water inlet hose is not long enough, contact

a  specialist  store  or  an  authorised  technician.

 Always use the new water inlet hoses supplied

with  the  machine.

Downloaded From WashingMachine-Manual.com Manuals

Содержание AQ D 169 PM Series





















Отзывы: