Hotpoint 23 Series Скачать руководство пользователя страница 34

Страница: 34 / 40

Before you call for service…

Problem

Possible Causes

What To Do

Frequent “buzzing” sound

Icemaker power switch is in the on

•

Set the power switch to the off position. Keeping it in the on position

position, but the water supply to the

will damage the water valve.

refrigerator has not been connected.

Ice cubes have odor/taste

Ice storage bin needs cleaning.

•

Empty and wash bin. Discard old cubes.

Food transmitting odor/taste to ice

•

Wrap foods well.

cubes.

Interior of refrigerator needs cleaning.

•

See

Care and cleaning.

Small or hollow cubes

Water filter clogged.

•

Replace filter cartridge with new cartridge or with plug.

Slow ice cube freezing

Door left open.

•

Check to see if package is holding door open.

Temperature control not set cold

•

See

About the controls.

enough.

Cube dispenser does

Icemaker turned off or

•

Turn on icemaker or water supply.

not work

water supply turned off.

Ice cubes are frozen to

•

Remove cubes.

icemaker feeler arm.

An item is blocking or has fallen

•

Remove any item that might be blocking, or has fallen into, the chute.

into the ice chute inside the top
door bin of the freezer.

Irregular ice clumps in storage

•

Break up with fingertip pressure and discard remaining clumps.

container.

•

Freezer may be too warm. Adjust the freezer control to a colder
setting, one position at a time, until clumps do not form.

Dispenser is

LOCKED

•

Press and hold the

LOCK CONTROL

pad for 3 seconds.

Water has poor taste/odor

Water dispenser has not been

•

Dispense water until all water in system is replenished.

used for a long time.

Water in first glass

Normal when refrigerator is first

•

Wait 24 hours for the refrigerator to completely cool down.

is warm

installed.

Water dispenser has not been

•

Dispense water until all water in system is replenished.

used for a long time.

Water system has been drained.

•

Allow several hours for replenished supply to chill.

Water dispenser does

Water supply line turned

•

See

Installing the water line.

not work

off or not connected.

Water filter clogged.

•

Replace filter cartridge or remove filter and install plug.

Air may be trapped in the water

•

Press the dispenser arm for at least two minutes.

system.

Dispenser is

LOCKED

•

Press and hold the

LOCK CONTROL

pad for 3 seconds.

Water spurting from

Newly-installed filter cartridge.

•

Run water from the dispenser for 3 minutes (about six liters).

dispenser

Water is not dispensed

Water in reservoir is frozen.

•

Call for service.

but icemaker is working

Refrigerator control setting

•

Set to a warmer setting.

is too cold.

No water or ice cube

Supply line or shutoff

•

Call a plumber.

production

valve is clogged.

Water filter clogged.

•

Replace filter cartridge or remove filter and install plug.

Dispenser is

LOCKED

•

Press and hold the

LOCK CONTROL

pad for 3 seconds.

Содержание 23 Series









































Результаты поиска

Содержание 23 Series

Отзывы:

Похожие инструкции для 23 Series

Бренды по названию

Популярные бренды

Hotpoint 23 Series, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание 23 Series

Отзывы:

Похожие инструкции для 23 Series

Бренды по названию

Популярные бренды