22
GB
●
DISPLAY
The display shows either the amount of time delay
remaining or an indication of the amount of time left for
a drying programme.
The delay time is displayed in hours and counts down
each minute.
The time to end is displayed in hours and minutes and
counts down each minute, this includes the cool
tumble phase. When timed programmes are selected
the time displayed throughout the cycle is the actual
time remaining.
When a sensing programme is selected the time
displayed is an estimate of the time remaining. When
the programme is selected the display shows the time
required to dry a full load, after around 10 minutes the
controller calculates a better estimate of the cycle time.
The colons between the hours and minutes in the
display flash to show that the time is counting down.
When the programme finishes its cool tumble phase
the display will show .
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by
a fault code number (
see Troubleshooting
).
●
Door Opening
Opening the door (or pressing the Start/Pause button
(Départ/Pause) ) during a programme will stop the
dryer and have the following effects:
●
The Start/Pause (Départ/Pause) light flashes Amber.
●
During a delay phase the delay will continue to
count down. The Start/Pause button (Départ/Pause)
must
be pressed to resume the delay programme.
The progress lights will change to show current
status.
●
During the drying part of the programme, the
time to end count continues but the colons do not
flash. The Start/Pause button (Départ/Pause)
must
be pressed to resume the programme. The
progress lights will change to show the current
status.
●
During the post creasecare (Anti-froissage Fin de
Cycle) phase of a drying programme, the
programme will finish. Pressing the Start/Pause
button (Départ/Pause) will re-start a new
programme at the beginning.
●
The Start/Pause button (Départ/Pause)
must
be pressed to resume the programme. The
progress lights will change to show the current
status and the Start/Pause (Départ/Pause) light
will stop flashing and turn green.
●
Changing the programmes knob will select a new
programme and the Start/Pause (Départ/Pause)
light will flash green. You can use this to select the
Cool Tumble programme to cool the clothes, if you
find them dry enough. Press the Start/Pause button
(Départ/Pause) to begin a new programme.
●
Note
If you have a power cut, switch off the power or
remove the plug. When the power is restored, press
the Start/Pause button (Départ/Pause) and the
programme will resume.
●
PROGRAMMES knob
!
Warning
, if after pressing the Start/Pause button
(Départ/Pause) the programme knob position has
changed, the new position will
NOT
change the
programme selected.
To change a selected programme, press the Start/Pause
button (Départ/Pause) , the light flashes Amber to
indicate the programme is paused. Select the new
programme and any options required, the light will then
flash green. Press the Start/Pause button (Départ/Pause)
again and the new programme will start.
●
OPTION buttons / lights
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected on the programme knob before
an option can be selected. Not all options are available
for all programmes (
see Start and Programmes
). If an
option is not available and you press the button, the
buzzer will beep three times. If the option is available
there will be one beep and the option light next to the
button lights to confirm the selection.
After the Start/Pause button (Départ/Pause) has been
pressed, only the Pre Creasecare (Anti-froissage
Début de Cycle) and Post Creasecare (Anti-froissage
Fin de Cycle) options can be changed.
Time Delay
(Départ Différé)
The start of some programmes (
see Start and
Programmes
) can be delayed for up to 24 hours.
Press this button, the display shows and the
option light comes on. Press again and a 1 hour delay
is selected and the display indicates 1hr, each further
press of the button adds 1hr to the delay. When 24hr
is displayed a further press the display shows
and after a couple of seconds cancels the delay. You
can also cancel the delay by pressing the ON/OFF
button.
Pre Creasecare
(Anti-froissage Début de Cycle)
This option is only available if a delayed start has
been selected. It tumbles the clothes occasionally
during the delayed period to help prevent creases
developing.
High Heat
(Intensif)
Available for Timed Drying programmes. Press this
button and a high heat setting is selected and the
light next to the button comes on.
Timed programmes have a default of low heat, if the
light next to the button is on then pressing this button
selects a low heat setting and the light goes out.
Post Creasecare
(Anti-froissage Fin de Cycle)
When available and selected, the clothes are
occasionally tumbled after the end of the drying and
cool tumble cycles, to help prevent creases
developing should you not be available to remove the
load immediately the programme is complete.
OFF
OFF
E88
The Controls
Start and Programmes
