Hoshizaki SRK-13H Скачать руководство пользователя | Manualshive

Страница: 17 / 53

background image

17

f) LED Lights and Audible Alarm Safeties

The red LED indicates control voltage (10 to 1V at K) and will remain on unless a
control voltage problem occurs. At startup a 5 second delay occurs while the board
conducts an internal timer check. A beep occurs when the control switch is moved to the
"ICE" position.
The green LEDs 1 through 4 energize and sequence from initial startup as listed in the
table below. Note that the order of the LEDs from the outer edge of the board is 1, 4, 3, .
For more information, see "II.B. Sequence of Operation."

Sequence Step

LED

Energized

Components

Time LEDs are On

Min.

Max.

Avg.

1 Minute Fill Cycle 4

FWV

60 seconds

Harvest Cycle

1, 4 and

HWV, HGV,
Comp,FMR

minutes

0 minutes 3 to 5 minutes

Last 50 seconds of harvest, HWV de-energizes and PM energizes
(LEDs 1, 3 and are on)
Freeze Cycle

1 (and 4 at
refills)

Comp, PM,
FMR, LLV
(FWV at
refill)

5 minutes

freeze timer
setting

30 to 35 minutes

Pump-Out

1, 3 and

Comp, HGV,
PM, DWV,
FMR

10 seconds 0 seconds factory setting

The built in safeties shut down the unit and have alarms as listed below.

No. of Beeps

(every 3 sec.)

Type of Alarm

Notes

1

High Evaporator Temp.
(temperature > 17°F)
(53°C)

Check for harvest problem (stuck HGV or
relay), hot water entering unit, stuck HM or
shorted thermistor.

Harvest Backup Timer
(harvest > 0 min. for two
cycles in a row)

Check for open thermistor, HGV not opening,
TXV leaking by, low charge or inefficient Comp.

3

Freeze Timer
(freeze > specified setting
for two cycles in a row)
Timer is factory set using
S4 dip switch 9 & 10

Check for a float switch stuck closed (up), HWV
or FWV leaking by, HGV leaking by, TXV not
feeding properly, low charge, HM not bypassing
or inefficient compressor.

To reset the above safeties, press the alarm reset button with the power supply on.

6

Low Voltage
(9Vac ±5% or less)

Red LED will turn off if voltage protection oper-
ates.
The control voltage safeties automatically reset
when voltage is corrected.

7

High Voltage
(147Vac ±5% or more)

Legend:

Comp–compressor; DWV–drain water valve; FMR–remote fan motor; FWV–fill

water valve;

HGV–hot gas valve; HM–headmaster; HWV–harvest water valve;

LLV–liquid line valve; PM–pump motor; TXV–thermostatic expansion valve

«
...
15
16
17
18
19
...
»

Содержание SRK-13H






















































Отзывы:

Нет отзывов

Похожие инструкции для SRK-13H

Бренд: Oerlikon Barmag Страницы: 36

Nessie Plug&Spray NPS 1CS

Бренд: Danfoss Страницы: 12

Бренд: Plein Air Страницы: 12

Бренд: Gardenline Страницы: 28

Бренд: Daikin Страницы: 44

Smartmax Series

Бренд: ubbink Страницы: 29

Бренд: Kayoba Страницы: 6

Бренд: Bryant Страницы: 54

Бренд: LVI Страницы: 8

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

F 550 GS Series

Бренд: Flux Страницы: 116

Бренд: Red Jacket Страницы: 42

Бренд: salmson Страницы: 48

Бренд: RADtec Страницы: 7

JUNG PUMPEN SIMER 4

Бренд: Pentair Страницы: 10

Бренд: Goldair Страницы: 4

Бренд: Waterhouse Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды