Hoshizaki KM-520MRJZ Скачать руководство пользователя страница 31

Страница: 31 / 41

For Standard Ice Storage Bins, Hoshizaki DB and DM Dispenser Units, and Coca-Cola
Freestyle

Dispenser Units

Application

Bin Control Ice Level Settings

Bin Control Setting

Shutdown Distance from Bin Control Lens
(Restart is 4 in. (102 mm) below shutdown distance)

Standard Ice Storage Bins

(Factory Default)

254 mm (10")

Do not adjust dispensers to this setting.

Hoshizaki DB and DM Dispensers

305 mm (12")

Coca-Cola Freestyle

Dispensers

406 mm (16")

Optional Setting

508 mm (20")

610 mm (24")

WARNING

Confirm that the final ice level location does not allow for icemaker movement,
water leakage, or ice overflow.

Fig. 14

Recommended Setting for

Hoshizaki DB and DM Dispensers

Recommended Setting for Coca-Cola Freestyle

Dispensers

Icemaker

Hoshizaki DB-200H

Dispenser Unit

Model Shown:
KM-520MAJ with DB-200H

Model Shown:
KM-660MAJ with B-300SF

Icemaker

Standard Ice

Storage Bin

Turn dial to adjust to

proper setting

Factory Default for Standard Ice

Storage Bins

WARNING!

Do not use this

setting with dispensers.

Bin Control
Lens

Setting #1

Setting #3
Setting #4
Setting #5

Setting #2

Bin Control
Lens

Setting #1

Setting #3
Setting #4
Setting #5

Setting #2

Control Board

Bin Control Setting

Содержание KM-520MRJZ










































Результаты поиска

Содержание KM-520MRJZ

Отзывы:

Похожие инструкции для KM-520MRJZ

Бренды по названию

Популярные бренды

Hoshizaki KM-520MRJZ, Инструкция по эксплуатации

Результаты поиска

Содержание KM-520MRJZ

Отзывы:

Похожие инструкции для KM-520MRJZ

Бренды по названию

Популярные бренды