Hoshizaki KM-1301SRJZ Скачать руководство пользователя | Manualshive

Страница: 41 / 45

background image

41

Sanitizing Rinse 3

25) Turn the cleaning valve to the right until completely horizontal (closed). Move the control

switch to the "ICE" position, then replace the front panel. After 3 min., remove the front
panel, then move the control switch to the "OFF" position.

26) Turn the cleaning valve to the left until completely vertical (open). Move the control

switch to the "WASH" position, then replace the front panel. After 5 min., remove the
front panel, then move the control switch to the "OFF" position.

27) Remove the front insulation panel, then remove the drain plug. After the water tank has

drained, replace the drain plug and front insulation panel.

28) Clean the dispenser unit/ice storage bin liner using a neutral cleaner. Rinse thoroughly

after cleaning.

29) Turn the cleaning valve to the right until completely horizontal (closed), then move the

control switch to the "ICE" position. Note: If on a dispenser unit, turn on the dispenser
unit power supply.

30) Replace all panels in their correct positions.

«
...
39
40
41
42
43
...
»

Содержание KM-1301SRJZ














































Отзывы:

Нет отзывов

Похожие инструкции для KM-1301SRJZ

Бренд: Tassimo Страницы: 14

Бренд: BARMATIC Страницы: 32

Midori Sno-King 1888W

Бренд: Gold Medal Страницы: 12

Бренд: Jura Capresso Страницы: 14

Бренд: Melissa Страницы: 25

Бренд: Hoshizaki Страницы: 33

Бренд: Magic Chef Страницы: 20

Horeca Large 380

Бренд: Rheavendors Group Страницы: 33

60-CUP COFFEE URN

Бренд: Hamilton Beach Страницы: 15

Бренд: emerio Страницы: 60

Бренд: Ratio Страницы: 21

Бренд: Hoshizaki Страницы: 88

Бренд: West Bend Страницы: 4

Бренд: Concept2 Страницы: 76

Бренд: Klarstein Страницы: 96

Бренд: Laspaziale Страницы: 24

Happy Maker 2.0

Бренд: Arissto Страницы: 46

Бренд: Hendi Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды