Hoshizaki KM-1100MAH Скачать руководство пользователя | Manualshive

Страница: 13 / 39

background image

13

• Remove the package containing the accessories.
• Remove the protective plastic film from the panels. If the appliance is exposed to the

sun or to heat, remove the film after the appliance cools.

• Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the

fan blade (if applicable) turns freely.

• Check that the compressor is snug on all mounting pads.
• The icemaker can be installed on a dispenser unit or ice storage bin. The ice storage

bins listed below are recommended.

Model Number Bin Width

Recommended Hoshizaki Ice Storage Bin

KM-1100M_H
KM-1340M_H
KM-1601MRH/3

30" or Wider B-500 Series

For further options, contact your local Hoshizaki distributor.

•

NOTICE!

Remote models must be connected to an appropriate remote condenser

unit. The remote condenser units listed below are recommended. Connection to a
different remote condenser unit will void the warranty unless Hoshizaki approves
a different remote condenser unit for your specific application. For further
details, contact your local Hoshizaki distributor.

Model Number Recommended Hoshizaki Remote Condenser Unit

KM-1100MRH
KM-1340MRH

URC-14F

KM-1601MRH/3 URC-22F

C. How to Remove Panels

See Fig. 1

• Front Panel: Remove the screw. Lift up and

pull towards you.

• Top Panel: Lift up at front slightly, push

rearward and lift off.

• Right Side Panel: Remove the screw. Slide

forward slightly and lift off.

• Insulation Panel: Lift up slightly, and pull

towards you.

Fig. 1

Top Panel

Right

Side

Panel

Front

Panel

Insulation Panel

«
...
11
12
13
14
15
...
»

Содержание KM-1100MAH








































Отзывы:

Нет отзывов

Похожие инструкции для KM-1100MAH

Бренд: Tassimo Страницы: 14

Бренд: Taylor Страницы: 32

Бренд: Bartscher Страницы: 52

Бренд: Bartscher Страницы: 30

Бренд: IDZOR Страницы: 2

Бренд: U-Line Страницы: 48

Бренд: U-Line Страницы: 32

Бренд: Buffalo Страницы: 56

Бренд: Pacific Страницы: 13

Бренд: Comobar Страницы: 12

Бренд: Jata calor Страницы: 20

Бренд: Rowenta Страницы: 98

Бренд: Qilive Страницы: 104

A MODO MIO premium

Бренд: Saeco Страницы: 60

Бренд: Vitek Страницы: 32

Бренд: Clatronic Страницы: 39

PerfectCoffee MC 08

Бренд: Waeco Страницы: 124

Бренд: Rommelsbacher Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды