manualshive.com logo in svg

Hoshizaki IM-500SAB, Инструкция по эксплуатации

Поделиться
Скачать
Hoshizaki IM-500SAB Скачать руководство пользователя страница 15

H. Startup

 WARNING

• All parts are factory-adjusted. Improper adjustments may adversely affect safety, 

performance, component life, and warranty coverage.

• Do not put your hands into the back of the storage bin or the baffle on top of the 

storage bin. Ice may drop off the icemaker, a hard block of ice may suddenly 
break down, or the icemaking mechanism may suddenly move, resulting in injury.

NOTICE

• If the appliance is turned off, wait for at least 3 minutes before restarting the 

appliance to prevent damage to the compressor.

• To prevent damage to the water pump, do not leave the control switch in the 

“WASH” position for extended periods of time when the water tank is empty.

• At startup, confirm that all internal and external connections are free of leaks.

1) Open the water supply line shut-off valve(s).
2) Remove the front panel.
3) Move the control switch to the “ICE” position.
4) Replace the front panel in its correct position.
5) Turn on the power supply and allow the icemaker to operate for a total of 10 minutes.
6) Remove the front panel, then move the service switch to the “OFF” position. 
7) Replace the front panel in its correct and allow the icemaker to drain for 2 minutes.
8) Turn off the power supply. 
9) Remove the front panel, then move the control switch to the “ICE” position. Replace the 

front panel in its correct position.

10) Clean the ice storage bin liner using a neutral cleaner. Rinse thoroughly after cleaning.
11) Turn on the power supply to start the automatic icemaking process.
12) During the first 5 minutes of the freeze cycle, confirm bin control operation by pressing 

and holding the bin control’s actuator paddle until the icemaker shuts down. The 
icemaker should shut down in approximately 15 seconds.

15

Содержание IM-500SAB























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды