background image

 

WARNING

 

The appliance should be destined only to the use for which  it has been expressly 
conceived. Any other use should be considered improper and therefore dangerous.  
The  manufacturer  cannot  be  held  responsible  for  injury  or  damage  resulting  from 
improper,  incorrect,  and  unreasonable  use.  Failures  to  install,  operate,  and 
maintain the appliance in accordance with this manual will adversely affect safety, 
performance, component life, and warranty coverage. 

To reduce the risk of death, electric shock, serious injury, or fire, follow basic 
precautions including the following: 

 

• Only qualified service technicians should install and service the appliance. 
 
• The appliance must be installed in accordance with applicable national, state, and 

local codes and regulations. 
 

• Appliance  is  heavy.  Use  care  when  lifting  or  positioning.  Work  in  pairs  when 

needed to prevent injury or damage. Do not lift using the top section or the doors. 

 
• To  reduce the  risk  of  electric  shock,  do not touch  the plug  or  power  switch  with 

damp hands.  

 
• Make  sure  the  power  switch  is  in  the  “OFF”  position  before  plugging  in  or 

unplugging the appliance the risk of electric shock. 

 
• Before  servicing,  move  the  power  switch  to  the  “OFF”  position.  Unplug  the 

appliance from electrical outlet. 

 
• This  appliance  requires  an  independent  power  supply  of  proper  capacity.  See 

name  plate  for  electrical  specifications.  Failure  to  use  an  independent  power 
supply of proper capacity can result in a tripped breaker, blown fuse,  damage to 
existing wiring, or component failure. This could lead to heat generation or fire. 

 
• 

THE  APPLIANCE  MUST  BE  GROUNDED:

  The  appliance  is  equipped  with  a 

NEMA 5-15 three-prong grounding plug 

  to reduce the risk of  potential shock 

hazards.  It  must  be  plugged  into  a  properly  grounded,  independent  3-prong  wall 
outlet.  If  the outlet is a 2-prong outlet,  it is your personal responsibility to have  a 
qualified electrician replace it with a properly grounded, independent 3-prong wall 
outlet.  Do  not  remove  the  ground prong from  the power  cord  and  do not  use  an 
adapter  plug.  Failure  to  follow  these  instructions  may  result  in  death,  electric 
shock, or fire. 

IMPORTANT SAFETY INFORMATION 

Throughout this manual, notices appear to bring your attention to situations which could 
result in death, serious injury, damage to the appliance, or damage to property.  
 

WARNING  

Indicates a hazardous situation which could result in death or 

 

 

 

 

serious injury.  

NOTICE

 

 

Indicates a situation which could result in damage to the 

 

 

 

 

appliance or property. 

IMPORTANT

 

Indicates important information about the use and care of the 

 

 

 

 

appliance. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание HD-2D-59


















Отзывы: