Hoshizaki DBF-25SB-AU Скачать руководство пользователя страница 11

Страница: 11 / 11

2. Do not damage the power cord. It should not be additionally

processed, jerked, bundled, weighed down or caught in. It

could cause electric shock or fire.

3. The unit must have a separate power supply. Branching off

the power cord, using an extension cord, or sharing a single

power supply with other appliances may result in electric

shock, heat generation or fire.

Check that:

* The attachment plug blades and their vicinity and the receptacle are

free of dust. Clean them if necessary.

* The attachment plug and power cord are not damaged, weighed

down or caught in.

* The attachment plug is plugged into a separate receptacle.

3. COOLING WATER (BIANNUALLY)

1) Unplug the unit.

2) Remove the top cover and inner cover.

3) Check that the cooling water level is about 2 cm below the top of

the water tank (DBF-25SB-AU) or up to the standard water level

marked on the tank (DBF-43SB-AU). If it is insufficient, refill the

water tank with tap water. Refresh the cooling water twice a year.

To refresh the cooling water:

4) Remove the drain pan.

5) Prepare a large container to receive drain water [about 6 L (DBF-

25SB-AU) or 8 L (DBF-43SB-AU) in ice storage]. Remove the drain

plug, and drain the water tank. After the cooling water has drained

out, refit the drain plug.

6) Refill the water tank according to “I. 5. [a] COOLING WATER

SUPPLY”.

7) Refit the top cover and inner cover.

8) Plug in the unit.

IMPORTANT

Dust, bacteria, and moisture in the air may cause contamination

or reduction in conductivity of the cooling water. To prevent

clogging of the overflow hose or inadequate ice storage, refresh

the cooling water twice a year.

If the cooling water conductivity reduces and no ice is produced

in the water tank, fill 1/3 (2 g) of the nozzle cap with baking

soda. Do not use an excessive amount of baking soda or any

other substances such as salt, vinegar, and juice. They will

corrode the stainless steel and copper tubes and cause failure.

1/3 (2 g)

Nozzle cap (accessory)

V. LONG STORAGE, RELOCATION, DISPOSAL,

TRANSFER

* When shutting down the unit for more than a week, carry out the

following maintenance procedures to clean and drain the beer

circuit and to keep the unit clean:

III. 4. CLEANING BEER CIRCUIT WITH SPONGE

5. DISASSEMBLY AND CLEANING OF BEER TAP

6. KEG COUPLER

7. EXTERIOR

8. AIR FILTER

Drain the water tank according to “IV. 4. COOLING WATER”. It

takes a few days to melt ice left in the water tank. After melting all

the ice, drain the water tank again, and dry the tank interior.

* In case of relocation or disposal of the product, contact an

authorized Hoshizaki service company.

* When selling or transferring this product, tape this instruction

manual to the exterior to provide the new owner with information on

safe and proper use of the product.

Содержание DBF-25SB-AU












Результаты поиска

Содержание DBF-25SB-AU

Отзывы:

Бренды по названию

Популярные бренды

Hoshizaki DBF-25SB-AU, Инструкция по эксплуатации

Результаты поиска

Содержание DBF-25SB-AU

Отзывы:

Бренды по названию

Популярные бренды