Hortus 211-393, Инструкция по эксплуатации

Страница: 5 / 12

5
Preparation
Unpack the carton. Take out the accessories pack from the carton of the heater body. Make sure the 1.
accessories listed in the above Accessories Check List are included. If anything missing, ask the retailer
immediately to provide it to you.
Prepare a cross head screw driver. 2.
Read this instruction manual carefully before installation and use. Keep this instruction manual in a 3.
proper and safe place for future use in case needed.
Installation
Take out the Main Body, Base (#7), Base Cover (#3), Table Top (#9) from the cartons. 1.
Put the Main Body up-side-down on a flat floor. (Fig. A). Slide Base Cover (#3) onto Base Bracket (#8) 2.
respectively. For easy assembly, let the Base Brackets (#8) get though the holes on Base Cover (#3)
one by one. Fix Base Cover (#3) and Base Steel Board (#2) onto Main Body with 4 Screws ST4x18(#1)
and 4 spring washers Ø4.2 (#14).
Put Base (#7) into Base Cover (#3) (Fig. B). Clip the power supply cord with Cord Clip (#18) and fix it 3.
onto Base (#7) with Screw M4x28 (#19) (Fig.C).
Put Washer Board (#6) with Screw M6x30 (#5) onto the holes of Base (#7), in which Base Brackets (#8) 4.
are located. Fix them onto Base Bracket (#8) with the provided Allen Key. (Fig. B).
Put Table Top (#9) on top of the Heater Body. Make sure the screw holes on Table Fixture (#10) are 5.
matching the holes on Top Steel Board (#12). Fix Table Top (#9) onto Heater Body with 4 Screws M6x8
(#11) and 4 spring washers Ø6.2 (#13).
Operations
Plug in the unit to a socket. Make sure the power supply is same as rated. 1.
Press Switch to switch on the power. Heater is shifted to Standby mode. Power Indicator Light starts 2.
flashing.
Press “MODE” button on the control panel or on the remote controller to switch on or to shift it to 3.
different power of the heater, Low (Green Light), High (Red light).
Press “OFF” button to shift the heater to standby mode. The indicator light starts flashing again. 4.
Press Switch again to cut off the power totally in case the heater is not to be used for a long time. 5.
No. Part Name No. Part Name
1 Tapping Screw ST4x18 13 Spring Washer Ø6.2
2 Base Steel Board 14 Spring Washer Ø4.2
3 Base Cover 15 Receiver
4 Lower Control Box 16 Standby Button
5 Screw M6x30 17 Mode Button
6 Washer Board 18 Cord Clip
7 Base 19 Screw M4x28
8 Base Bracket 20 Plug
9 Table Top 21 Power Indicator Light
10 Table Fixture 22 Remote Control
11 Screw M6x8 23 Switch
12 Top Steel Board
Parts Descriptions:
Accessory Name Qty Accessory Name Qty
Allen Key 1 Screw M6x8 4
Tapping Screw ST4x18 4 Washer Board 1
Base Steel Board 1 Cord Clip 1
Screw M6x30 2 Screw M4x28 2
Spring Washer Ø6.2 4 Spring Washer Ø4.2 4
Accessories Pack Check List:
Model no. SH1675J7R-2
Art. No. 211-393
Power source 220-240V AC ~ 50 Hz
Consumption 1350-1600W
Protection class IP55
Product specifications