horsch LEEB PT 330 Скачать руководство пользователя страница 47

Страница: 47 / 203

3.3.3 Rotating beacon

The rotating beacon (4) can be adjusted to the

side or down by hand.

NOTE

In some countries it is mandatory to switch on

the rotating beacon when driving on public roads.

Pay attention to and comply with the corre-

sponding country specific regulations!

3.3.4 Boom illumination

Two spotlights (5) are mounted on the tank to

illuminate the lateral work area.

Folding boom lighting is controlled via the terminal.

3.3.5 NightLight (optional)

Extremely bundled light (LED spotlight) to illu-

minate the spraying cones.

NightLight is controlled with the software of the

control terminal.

NightLight (6) used in the field

At the headland the lights (6) are automatically

cleaned by a washing facility. The LED spotlights

are controlled via the terminal.

Содержание LEEB PT 330












































































































































































































Результаты поиска

Содержание LEEB PT 330

Отзывы:

Похожие инструкции для LEEB PT 330

Бренды по названию

Популярные бренды

horsch LEEB PT 330, Руководство по эксплуатации

Результаты поиска

Содержание LEEB PT 330

Отзывы:

Похожие инструкции для LEEB PT 330

Бренды по названию

Популярные бренды