HORNE T105A Скачать руководство пользователя страница 4

Horne Engineering Ltd 

Issue 7, November 2018 

 

 

 

 

4

 

Fig 4.   NB It is important to use the supplied screw bushes.   

 

Fig 5. 

 

 

 

 

7)  Connect the Supply Pipes 

N.B.  Ensure that the top cover of the pre-plumbed enclosure is replaced prior to connecting up the 
supply pipes. The fitting of isolation valves is required as close as practicable to the water supplies 
inlets of the shower panel. 
 
Connect the hot water supply to the left hand inlet, and cold water to the right-hand inlet (See Fig 5). 
 

DO NOT OPEN THE WATER SUPPLIES AT THIS STAGE AS THEY HAVE NOT BEEN FLUSHED 
OUT  TO  REMOVE  THE  DEBRIS  IN  THE  PIPEWORK.    SUCH  DEBRIS  CAN  DAMAGE  THE 
THERMOSTATIC VALVE. 

 

 

 

8)  Flush the Pipework 

Flush  out  the  pipework  in  accordance  with  Water  Bylaws  2000  (Scotland)  and  BS  6700:  1997 
(England  &  Wales).    The  use  of  a  Horne  flushing  kit  is  strongly  recommended,  because  this 
connects  directly  to  the  water  inlets  to  the mixing  valve.    Access  to  the flushing points  is gained 
from  underneath  the  casing  through  the  lower  end  cap.    Isolate  the  water  supplies  and  also  the 
low level servicing valves located on the side of the panel (see Fig 6) using the supplied 4mm hex 
key.  Remove the strainer cap  with the strainer basket and screw in the flushing adapter.  Place 
the end of the flushing hose in an appropriate drain or container and turn on the supply to flush as 
required.    After  flushing,  remove  the  flushing  adapter  and  replace  the  strainer  cap.    Repeat  for 
both hot and cold supplies.  See Figs 6 and 7.

  

 
NOTE THAT IF THERE IS ANY DANGER OF FREEZING THEN THE PIPES AND TSV1-3 MUST 
BE DRAINED TO AVOID DAMAGE.

 

 

 

 

 

 

Содержание T105A

















Отзывы: