background image

On/Off Switch

Backlit Reader

6

Battery Power Mode

When the RAPiD

®

 safe is unplugged, and is operating on battery power, 

you must press 

the ENTER key to activate system.

 

Pressing the ENTER key causes the system to achieve ready status. This includes RFID tag 
reading and keypad operation.

For example:

 To open your safe with an RFID tag, while the system is running on 

battery power, first press the ENTER key to bring it to ready status. Place your RFID tag 
approximately 1/2" over the RFID reader to open the safe. 

To open your safe with your keypad code, first press the ENTER key to bring it to ready 
status. Enter your code on the keypad followed by ENTER, to open the safe.

Backlit Reader 

Your safe’s backlit reader remains on 
while the system is plugged into an 
electrical outlet, unless you switch it off. 
The backlit reader will switch off when the 
system times out for 20 seconds under 
battery power only. 

To turn the light off (when using electrical 
power), open the safe, and locate the  
on/off switch next to the white program 
button.

Keypad Status Light Codes

When the light 
displays:

It means:

Solid Red 

The system is 
powered and ready.

Blinking Amber

The system is ready to 
program.

Solid Amber

The battery is low. 
Replace batteries 
immediately.

Solid Green

The system is 
unlocking.

Содержание 98150













Отзывы: