manualshive.com logo in svg

HORN LHD6001+, Руководство по установке, Страница: 13 / 36

Поделиться
Скачать
HORN LHD6001+ Скачать руководство пользователя страница 13

-

9

-

Oper

4. Disarm the panic alarm: Press the disarm button, duress code and # to disarm when panic alarm happened. 

    Duress code is produced according to mater code or user's code. For example, if master code is 8889, the 

    duress code will be 8880, and 9990 if the master code is 9999. When disarm the system, after inputting this 

    duress code, the panel will call to alarm, but the siren will not siren even if it is set on.

5. For ARM the zones: After disarm or arm failure, press again the button again for 3S to force Arm the system. 

    This is not working for the conditions if there is alarm happened or during the entry delaying.

Arm or disarm the zone one by one

1. Arm single zone: Input user's code with #, then zones to which the input code has the right to control will be armed

2. Arm some zones: Press disarm button on the keypad, input user's code and # to disarm some zones.

3. Force arm some zones: Input user's code, then 1 with # to force arm the system if previous arm action invalid. 

    Then the zones under the control right of the input code will be force armed. For example, if user's code 5678

    has the right to control zone 3,5 and 8. Press disarm button, input user's code 5678 confimed with #, then 

    zone 3,5 and 8 will be disarmed.

After installed correctly, the keypad can be cancelled and the system can be operated as the instructions as below:

use the remote controller, key zone or telephone lines to Arm or disarm the system.

Power LED on the main board of panel will be on when AC power or backup battery connected, and ARM LED 

will be on when the whole system in Arm way status and flash when arm stay and off when disarm.

The buzzer will beep in every two minutes to show the system trouble of AC lose, low battery, PSTN lose, and 

siren trouble for 30 minutes.

The bell will turn on if no keypad is connected when the users use remote controller to arm or disarm this 

sytem, no matter what is set by command 44.

Operation without keypad

Содержание LHD6001+





































Отзывы:

Нет отзывов