EN
19
DX8e, DX8 (Gen2), DX9, DX18, DX20, iX12 and iX20
TIP:
It is possible to enable or disable the four servo aileron mix by assigning
a switch to the P-Mix instead of setting the switch to ON during setup in steps
8 and 9.
TIP:
If you want to use SAFE select with the Advanced model setup, you can
assign a switch to any channel 7-9 for SAFE select. Even though the AR637TA
only has 6 servo ports, it can use up to channel 9 to key SAFE Select.
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset),
then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to
100%
Set Throttle Cut to
-100%
DX6e
DX6G2
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE:
WING: 1 AIL 1 FLAP
4. Go to the Channel Assign
Channel Input Confi g: GEAR (channel 5): INH
5. Optional: Select a switch for channel 7 in Channel Assign if you wish to use
the reversing feature of the Avian Smart ESC
6. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP*
14% Elevator
POS 2: 100% FLAP*
20% Elevator
SPEED
2.0
7. Go to the FUNCTION LIST
8. Set MIXING: P-MIX 1
Select;
NORMAL
Set INH > INH to read FL > GEAR
RATE:
100% 0%
OFFSET:
0%
TRIM:
INH
Switch:
ON
9. Set MIXING: P-MIX 2**
Select;
NORMAL
Set INH > INH to read AIL > GEAR
RATE:
-100% -100%
OFFSET:
0%
TRIM:
INH
Switch:
ON
10. Set MIXING: P-MIX 3**
Select;
NORMAL
Set INH > INH to read AIL > FL
RATE:
100% 100%
OFFSET:
0%
TRIM:
INH
Switch:
ON
†
Some of the terminology and function locations used in the iX12 and iX20
programming may be slightly different than other Spektrum AirWare™ radios. The
names given in parenthesis correspond to the and iX20 programming terminology.
Consult your transmitter manual for specifi c information about programming your
transmitter.
* Flap programming values may vary slightly. For your initial fl ights use the
recommended fl ap travel settings provided in the Flaps section and adjust the fl ap
travel to your preference on subsequent fl ights.
** Adjust the percentages in P-Mix 2 and 3 to match the fl ap travel to aileron travel at
full alieron right and left.
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset),
then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to
100%
Set Throttle Cut to
-100%
DX8e
DX8
(Gen2)
DX9
DX18
DX20
iX12
iX20
1. Go to the SYSTEM SETUP (Model Setup)
†
2. Set MODEL TYPE: AIRPLANE
3. Go to CHANNEL ASSIGN:
CHANNEL INPUT CONFIG
AUX2
Switch
A
4. Set AIRCRAFT TYPE (Model Setup, Aircraft Type)
†
:
WING: 1 AIL 1 FLAP
5. Go to the SYSTEM SETUP
Digital Switch Setup: Switch A
Pos
0:
-100
Pos 1: -100 (NO MOTOR REVERSING)
Pos 1: 100 (MOTOR REVERSING)
6. Go to the Channel Assign
SELECT GEAR: INH
7. Optional: Select a switch for channel 7 in Channel Assign if you wish to use
the reversing feature of the Avian Smart ESC
8. Go to the FUNCTION LIST (Model Adjust)
†
9. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP*
14% Elevator
POS 2: 100% FLAP*
20% Elevator
SPEED
2.0
10. Set MIXING: P-MIX 1
Select;
NORMAL
Set INH > INH to read Normal FL > GEAR
RATE:
100% 0%
OFFSET:
0%
TRIM:
INH
Switch:
ON
11. Set MIXING: P-MIX 2**
Select;
NORMAL
Set INH > INH to read Normal AIL > GEAR
RATE:
-100% -100%
OFFSET:
0%
TRIM:
INH
Switch: ON (for constant) or select switch for activation
4-aileron mode ON/OFF.
12. Set MIXING: P-MIX 3**
Select;
NORMAL
Set INH > INH to read Normal AIL > FL
RATE:
100% 100%
OFFSET:
0%
TRIM:
INH
Switch: ON (for constant) or select the same switch as
choosen for P-MIX 2 for activation 4-aileron mode ON/OFF.