8
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
TREADMILL
OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES
9
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
TREADMILL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
PRE-ASSEMBLY
ASSEMBLY
STEP 1
DO NOT ATTEMPT TO LIFT THE TREADMILL!
Do not move or lift treadmill from
packaging until specified to do so in the assembly instructions. Failure to do so may
result in injury! Remove plastic wrap from console masts.
NOTE:
During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware.
Any grease, such as lithium bike grease is recommended.
WARNING
ASSEMBLY
STEP 1
FLAT WASHER (B)
20 mm
Qty: 1
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
BOLT (A)
15 mm
Qty: 1
TEFLON WASHER (C)
18 mm
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
HARDWARE BAG 1 CONTENTS :
TEFLON WASHER
(C)
ELEVATION FRAME
FLAT WASHER
(B)
BOLT (A)
LEFT CONSOLE MAST
BOLT (D)
MAIN FRAME
LEFT LINKAGE ARM
FLAT WASHER (E)
WAVY WASHER (F)
TEFLON WASHER
(C)
FLAT WASHER
(B)
BOLT (A)
LEFT CONSOLE MAST
BOLT (D)
MAIN FRAME
LEFT LINKAGE ARM
FLAT WASHER (E)
WAVY WASHER (F)
ELEVATION FRAME
A
Open
HARDWARE BAG 1
.
B
Cut banding straps. Do not move or lift treadmill from packaging.
C
Move
LEFT LINKAGE ARM
into position. Insert 1
BOLT (A)
and 1
FLAT WASHER (B)
into
LEFT
LINKAGE ARM
followed by 1
TEFLON WASHER (C)
and attach to
ELEVATION FRAME
.
D
Lift
LEFT CONSOLE MAST
into upright position. Be sure to hold the console mast firmly, as
it will not stay in the upright position on its own.
E
Insert 1
BOLT (D)
and 1
FLAT WASHER (E)
through
LEFT CONSOLE MAST
followed by
1
WAVY WASHER (F)
and attach to
MAIN FRAME.
ASSEMBLY
STEP 2
TEFLON WASHER
(C)
FLAT WASHER
(B)
BOLT (A)
LEFT CONSOLE MAST
BOLT (D)
MAIN FRAME
LEFT LINKAGE ARM
FLAT WASHER (E)
WAVY WASHER (F)
ELEVATION FRAME
MAIN FRAME
LOCK LATCH PIN (G)
RIGHT FOLDING FRAME
HARDWARE BAG 2 CONTENTS :
A
Open
HARDWARE BAG 2
.
B
Attach
LOCK LATCH PIN (G)
into
RIGHT FOLDING FRAME
using T-wrench and
tighten completely.
C
Pull
LEAD WIRE
through
RIGHT CONSOLE MAST
. After pulling the
LEAD WIRE
through the
mast, the top of the
CONSOLE CABLE
should be located at the top of the mast. Detach and
discard
LEAD WIRE
.
D
Continue STEP 2 on next page.
LOCK LATCH PIN (G)
Qty: 1
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
RIGHT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
SC2250T_OM_Rev.1.0.indd 8-9
3/23/10 9:55 AM
