manualshive.com logo in svg

horiba LAQUAact-EC110, Инструкция по эксплуатации

Поделиться
Скачать
horiba LAQUAact-EC110 Скачать руководство пользователя страница 10

For your safety

VIII

●

Operational precautions (battery)

 

・

Do not short-circuit a battery.

 

・

Set the + and 

 side of the battery correctly.

 

・

When the battery has run out or the instrument will not be used for a long time, remove

the batteries.

 

・

Of the specified battery types, make sure to use two batteries of the same type.

 

・

Do not use a new battery together with a used battery.

 

・

Do not use a fully charged nickel-metal hydride battery together with a partially

charged battery.

 

・

Do not attempt to charge a non-rechargeable battery.

●

Environmental conditions for use and storage

 

・

Temperature: 0°C to 45°C

 

・

Humidity: under 80% in relative humidity and free from condensation

Avoid the following conditions.

 

・

Strong vibration 

 

・

Direct sunlight 

 

・

Corrosive gas environment

 

・

Close to an air-conditioner 

 

・

Direct wind

●

Transportation

When transporting the instrument, repackage it in the original package box. Otherwise, it
may cause instrument breakage.

●

Disposal

 

・

Standard solution used for the calibration must be under neutralized before the

disposal.

 

・

When disposing of the product, follow the related laws and/or regulations of your

country for disposal of the product.

Содержание LAQUAact-EC110










































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды