2
GETTING TO KNOw yOUR ClEANER
A. Lower Cord Clip
B. Handle Release Button
C. Water Tank Cap
D. Clean Water Tank
E. Handle
F.
Upper Cord Clip
G.
Handle Pole
H. Power Lamp (Inside)
I.
On/Off Switch
J.
Cleaner Main Body
K. Floor Head
L.
Textile Pad
M.
Carpet Glider
N. Funnel
ASSEmBlING yOUR ClEANER
Remove all components from the packaging.
1. Insert the handle pole into the handle until it locks into position.
[1]
2. Insert the handle into the cleaner main body until it locks into position.
[2]
USING yOUR ClEANER
BEFORE yOU BEGIN ClEANING
1. Remove the clean water tank cap from the cleaner main body.
[3]
2. Fill the clean water tank with cold tap water.
[4]
Do not add any chemicals,detergents
or perfumes to the clean water tank
.
3.
Re-fit the tank cap and ensure good sealing.
[5]
4.
Attach the textile pad to the base of the floor head.
[6]
ImPORTANT: Always unplug the cleaner when adding water or changing a textile pad.
NOTE: wash the textile pad prior to use to remove any lint.
STEAm ClEANING HARd FlOORS
NOTE: Always sweep or vacuum the floor prior to use to remove any loose dirt or debris.
IMPORTANT:Do not use the cleaner without a textile pad attached to the floor head.
NOTE:
Do not use the carpet glider when cleaning hard floors.
1. Plug the steam cleaner into the main power and switch on the product.The power lamp
will illuminate after 20 seconds.
[7]
2. To produce
steam recline the cleaner by placing a foot on the floor head and lowering the
REFRESHING CARPETS
NOTE: Always sweep or vacuum the floor prior to use to remove any loose dirt or debris.
IMPORTANT: Do not use the cleaner without a textile pad attached to the floor head.
1.
Attach the carpet glider to the floor head.
[10]
2. Plug the steam cleaner into the main power. The power lamp will illuminate after 20
seconds.
3.
To produce steam recline the cleaner by placing a foot on the floor head and
lowering the main body towards the floor.
[8]
4. Move the cleaner slowly backwards and forwards paying particular attention to high
traffic areas.
[9]
ClEANER mAINTENANCE
IMPORTANT: Always ensure the cleaner has fully cooled down before performing
any maintenance tasks.
Empty the water tank
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2. Remove the water tank cap, pull off directly.
[3]
3. Empty any excess water from the tank.
[11]
Replace the water tank cap.
[5]
Removing and cleaning the textile pad
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2.
If necessary remove the carpet glider, then peel the textile pad from the floor base.
[12]
3.
Wash the textile pad in a washing machine with a mild detergent at max temperature 40°C.
ImPORTANT:
Do not use bleach or fabric softener when washing the textile pad.
Storage of appliance
Store the appliance in a dry area.
TROUBlE SHOOTING
Should you have a problem with the product, complete this simple user checklist before
calling your local Hoover service.
The steam stick will not switch on.
•
Check the unit is plugged in.
•
Check the power cord
The steam stick is not producing steam.
•
There may be no water in the clean water tank.
•
You may not have waited enough time after switching the cleaner on ( 20 seconds ).
main body towards the floor.
[8]
3.
Move the cleaner slowly backwards and forwards paying particular attention to high traffic
areas.
[9]
GB
