3
*Certain Models Only **May vary according to models
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
It is important to note that this vacuum cleaner is supplied with an Energy Label as
required by European Regulation (EU) 665/2013.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this
indicates that the vacuum cleaner is not suitable use on carpets.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then
this indicates that the vacuum cleaner is not suitable for use on hard floors.
#1
NOTE:
Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency
in accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
The crevice tool*, furniture nozzle* and dusting brush** are stored on the telescopic tube
through a practical accessories’ holder. They can be fitted to the handle or the end of
telescopic tube.
On certain models the dusting brush is conveniently integrated in the hose handle.
Crevice Tool*
– For corners and hard to reach areas.
[X1]
Dusting brush**
– For bookshelves, frames, keyboards and other delicate areas.
[X2]
Furniture Nozzle*
– For soft furniture and fabrics.
[X3]
Parquet Nozzle* –
For parquet floors and other delicate floors.
[AA]
Pet Hair Remover Mini Turbo Nozzle* -
Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hair removal.
[y]
Allergen Remover Mini Turbo Nozzle* –
Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal.
[Z]
IMPORTANT:
Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
ClEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
IMPORTANT:
To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the dust container pressing the bin release latch to detach the dust
container from the main cleaner and pull upward to remove.
[9]
2. Once the dust container is released from the main cleaner body, hold it by the handle
grip
and put it above a waste container. With the other hand press the bin flap
release button to open the container and release the dust.
[10]
3. Once emptied, close the bin flap and refit the dust container onto the cleaner
ensuring the hook has been positioned correctly in the main body.
[14]
Then lock
the container in place by pushing the container bin handle down until the latch
connects with the main body of the cleaner: you will hear a click when fully connected.
NOTICE: Ensure the power cord has been unplugged before emptying.
NOTIC
E: Ensure the bin flap has been closed before refitting it to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with pre- motor filter and exhaust filter. To maintain optimum cleaning
performance, regularly remove the filters and tap against the side of the waste container to
release dust. The filters should be washed every 5 dust container empties or when the filter
has excessive dust level.
IMPORTANT:
All bagless cleaners require regular filters cleaning. Failure to clean your filter
may result in air blockage, overheating and product failure. This may invalidate your guarantee.
IMPORTANT:
Regularly check and maintain the filters.
IMPORTANT:
Always ensure the filter pack is fully dry before use.
To access the pre-motor filter:
IMPORTANT:
Switch off and unplug the power cord before accessing the filters.
1. Release the dust container pressing the bin release latch to detach the dust container
from the main cleaner and pull upward to remove.
[9]
2. Release the pre-motor filter cover pressing the pre-motor filter cover latch and rolling
pre-motor filter cover on the opposite edge.
[15]
3. Remove the filter from main cleaner and wash it by hand using warm water. Do not
use hot water or detergents. Remove excess water from the filter and leave to dry
fully before reusing.
[16,19,20]
4. Refit it to the cleaner once fully dry. Press on the top of the filter to ensure it is back
into place.
[16]
5. Lock the pre-motor filter cover pressing at the top: you will hear a click once
the pre-motor filter cover fits into place.
[15]
6. Refit the dust container to the cleaner ensuring the hook has been positioned
correctly in the cleaner body. Then lock the container in place pushing the
container bin handle down until the latch connects with the main body of the cleaner:
you will hear a click when fully connected.
[14]
To access the exhaust filter located on the base of the cleaner.
1. Unlock the exhaust filter cover pressing two buttons and pulling outward from
the main cleaner.
[17]
2. Remove the filter pack pulling the ring-pull of the exhaust filter.
[18]
3.
Gently tap and wash the filter pack. Do not use hot water or detergents. Remove
excess
water from the filter and leave to dry fully before using.
[19,20]
4. Reassemble the filter pack once it is fully dry and refit it onto the cleaner inserting
back into the location.
5.
Lock the exhaust filter cover by pressing the edge with the clips: you will hear a click
once the exhaust filter door fits into place.
[17]
IMPORTANT:
Do not use the product without the filter pack fitted.
