background image

07 GB

2.3. ADAPTING THE HOB TO DIFFERENT
TYPES OF GAS

To  adapt  the  Hob  for  use  with  different  types  of  gas,  carry  out  the 
following instructions:
•Remove the grids and burners
•Insert on hexagonal spanner (7 mm) into the burner support 

(Figure 

7)

•Unscrew the injector and replace it with one suitable for the gas to be 
used

 (see gas type table)

2.4. REGULATING THE MINIMUM FLAME

After lighting the burners, turn the control knob to the minimum setting 
and then remove the knob (this can easily be removed by applying 
gentle pressure).
Using a small «Terminal» type screwdriver the regulating screw can 
be adjusted as in 

Figure 9.

 Turning the screw clockwise reduces the 

gas flow, whilst turning it anticlockwise increases the flow – Use this 
adjustment to obtain a flame of approximately 3 to 4 mm in length and 
then replace the control knob.
When the gas supply available is LPG - the screw to set the idle flame 
must be turned (clockwise) to the end stop.
When you have carried out the new gas regulation, replace the old gas 
rating plate on your appliance with one (supplied with hob) suitable for 
the type of gas for which it has been regulated.

3. USE OF HOB - USER INSTRUCTIONS

This  appliance  must  only  be  used  for  the  purpose  for  which  it  is 
intended,  domestic  cooking,  and  any  other  use  will  be  considered 
improper and could therefore be dangerous. The Manufacturer will 
not be responsible for any damage or loss resulting from improper 
use.

3.1. USING THE GAS BURNER

To ignite the burners, place a lighted taper close to the burner, press in 
and turn the control knob anti-clockwise.
If the burners have not been used for a couple of days, wait for a few 
seconds before lighting the burner, this will allow any air present in the 
pipes to escape.
For appliances fitted with electronic ignition carry out the following:
• Push in and turn the knob anticlockwise to the ignition symbol.
• İgnite the burner by pressing the sparker button.
For hobs fitted with automatic ignition simply push in and turn the knob 
to the ignition symbol.
The ignition system will continue to generate sparks as long as the 
control knob is being pressed.
If the burner has not ignited within 5 seconds, turn the knob to the 0 
position and repeat the operation.
For models fitted with a safety tap (which cuts-off the flow of gas if the 
flame  is  accidentally  extinguished)  the  burners  are  ignited  and 
described above, but care must be taken.
Prior to switching on the gas hob ensure that the burners and burner 
caps are correctly placed within their position.

GENERAL ADVISE

For best results, use cooking vessels with a flat surface.  The size of 
the surface should match the gas burner side as follows. Table A. 

Burner Type

Ø pan/pot 

(cm)

AUX 

SR

UR

QC

12 - 18

18 - 24

24 - 26

24 - 28

24 - 28

Auxiliary

Semi Rapid

Rapid

Ultra Rapid

Double Ring

Table A

Power

(kW)

1,00

1,75

2,50

3,50

4,00

G20/20 mbar

(methane)

95 l/h

167 l/h

238 l/h

333 l/h

381 l/h

G30/28-30 mbar

(LPG)

73 g/h

127 g/h

182 g/h

255 g/h

291 g/h

These  instructions  are  for  qualified  personnel,  installation  of  equipment 
must be in line with the relevant national standard.

 (For U.K. only: by law 

the  gas  installation\commissioning  must  be  carried  out  by  a  "Gas 
Safe"  installer)

All work must be carried out with the electricity supply disconnected.
The rating plate on the hob shows the type of gas with which it is designed to 
be used. Connection to the mains gas supply or gas cylinder should be 
carried out after having checked that it is regulated for the type of gas with 
which it will be supplied. If it is not correctly regulated see the instructions in 
the following paragraphs to change gas setting.
For liquid gas (cylinder gas) use pressure regulators which comply with the 
relevant national standards.
Use  only  pipes,washers  and  sealing  washers  which  comply  with  the 
relevant national standards.

For some models a conic link is furnished to outfit for the installation in the 
countries where this type of link is obligatory; in picture 8 it is pointed out 
how to recognize the different types of links (CY = cylindrical, CO = conic). 
In every case the cylindrical part of the link has to be connected to the hob.

2.2. GAS CONNECTION

4. MAINTENANCE AND CLEANING

Before  cleaning  the  hob,  ensure  the  appliance  has  cooled  down. 
Remove the plug from the socket or (if connected directly) switch off 
the electricity supply.

Cleaning and user maintenance shall not be made by children without 
supervision

Never  use  abrasives,  corrosive  detergents,  bleaching  agents  or 
acids. Avoid any acid or alkaline substances (lemon, juice, vinegar 
etc.) on the enamelled, varnished or stainless steel sections.

When  cleaning  the  enamelled,  varnished  or  chrome  sections,  use 
warm soapy water or a non caustic detergent. For stainless steel use 
an appropriate cleaning solution. 

The burners can be cleaned with soapy water. To restore their original 
shine, use a household stainless steel cleaner. After cleaning, dry the 
burners and replace.

It is important the Burners are replaced correctly.

Chromed grids and burners

Chromed grids and burners have a tendency to discolour with use.   
This does not jeopardize the functionality of the hob. 

Our After Sales Service Centre can provide spare parts if required.

For smaller containers the gas burner should be regulated so that the 
flame does not overlap the base of the pan. Vessels with a concave or 
convex base should not be used.

WARNING: If a flame is accidentally extinguished, turn the knob 
to the off position and do not attempt to re-ignite if for at least 1 
minute.

If over the years the gas taps become stiff to turn it is necessary to 
lubricate them.

Such  operation  must  be  carried  out  only  by  qualified  Service 
Engineers.

5. AFTERCARE

Before calling out a Service Engineer please check the following:
• that the plug is correctly inserted and fused;
• that the gas supply is not faulty.

If the fault cannot be detected:
Switch off the appliance and call the After Service Centre.  DO NOT 
TAMPER WITH THE APPLIANCE.

24 - 28

Triple Crown
Burner 

3,80

362 l/h

276 g/h

TC

Содержание HGH 64








Отзывы: