Honeywell X-618 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 38

background image

28

Figure 25 Schematic Diagram of the NRI Standby Power Supply Cable Connection

Connecting the DA Main and Standby Power Supply Cables

Connecting the Main Power Supply Cable

1. Strip off the wire jacket of one end of the prepared standby power supply cable by 20mm and

connect the cable to the main power supply wiring terminal, as shown below.

2. Tighten the screws, and cover the power supply interface set.

3. Insert the wiring terminal of the installed power supply cable into the main power supply input

port of the DA, and tighten the screws at both ends.

4. Insert the other end of the main power supply cable into the main power supply equipment.

Connecting the Standby Power Supply Cable

1. Strip off the wire jacket of one end of the prepared standby power supply cable by 20mm and

connect the cable to the standby power supply wiring terminal, as shown below.

«
...
32
33
34
35
36
...
»

Содержание X-618







































Отзывы:

Нет отзывов

Похожие инструкции для X-618

Бренд: Ultrasound Страницы: 6

Бренд: Aaron Страницы: 2

Бренд: DaytonAudio Страницы: 6

Бренд: Offel Страницы: 2

Бренд: DaytonAudio Страницы: 4

OBJECTIVE2+ODAC REVB

Бренд: JDS Labs Страницы: 9

Бренд: JL Audio Страницы: 17

Бренд: VINCENT Страницы: 64

JAMP-500HC06-SGR

Бренд: J&M Corporation Страницы: 6

Evidence Acoustics 50TUBE-BT

Бренд: Churchill Страницы: 12

Бренд: M-system Страницы: 2

PX3-3000 series

Бренд: Raritan Страницы: 875

BLACK PEARL 30 BP30

Бренд: Genz Benz Страницы: 8

Бренд: Takstar Страницы: 2

Subamp SBA-12000

Бренд: Lynx Страницы: 12

Бренд: Unika Страницы: 16

Бренд: Bugera Страницы: 15

Бренд: StetSom Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды