Honeywell VS8521 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 8

Honeywell VS8521 Скачать руководство пользователя страница 3

VS8521 VENTFREE MILLIVOLT GAS VALVE

3

69-1223—1

Fig. 3. Top view of gas valve with HI/LO regulator.

Fig. 4. Top view of gas valve with standard regulator.

Fig. 5. Proper use of wrench on gas valve.

WIRING

Follow the wiring instructions furnished by the appliance
manufacturer, if available, or use the general instructions
provided below. Where these instructions differ from the
appliance manufacturer, follow the appliance
manufacturer instructions. For typical wiring diagrams,
see Fig. 6.

All wiring must comply with applicable electrical codes
and ordinances.

Disconnect power supply before making wiring
connections to prevent electrical shock or equipment
damage.

1.

Check the power supply rating on the gas valve
and make sure it matches the available supply.
Install the transformer, thermostat, and other
controls, as required.

2.

This valve can be used only in a self-generating
system.

3.

Adjust the thermostat heat anticipator to the 0.1A
at 750 mV rating stamped on the valve operator.

TPTH

TP

L

HI

O

M10926

OFF

PILOT

ON

HI/LO
REGULATOR

TH

WIRING
TERMINALS

INLET
PRESSURE TAP

OUTLET
PRESSURE TAP

GAS
CONTROL KNOB

TPTH

TP

TH

M10927

OFF

PILOT

ON

OUTLET
PRESSURE
TAP

PRESSURE REGULATOR
ADJUSTMENT (UNDER
CAP SCREW)

WIRING
TERMINALS

INLET
PRESSURE TAP

GAS
CONTROL
KNOB

APPLY WRENCH
FROM BOTTOM OF
GAS CONTROL TO
SHADED AREA

M6916

«
1
2
3
4
5
...
»

Содержание VS8521









Отзывы:

Нет отзывов