Honeywell VR8215 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 8

Honeywell VR8215 Series Скачать руководство пользователя страница 8

VR8215S,T DIRECT IGNITION COMBINATION GAS CONTROLS

Automation and Control Solutions

Honeywell International Inc.

Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North

35 Dynamic Drive

Golden Valley, MN 55422

Toronto, Ontario M1V 4Z9

customer.honeywell.com

® U.S. Registered Trademark
© 2008 Honeywell International Inc.
69-2253—01 M.S. 08-08

To Turn ON Appliance

STOP! Read the Warnings

Above Before Proceeding.

1.

The lighting sequence on this appliance is
automatic;

do not attempt to manually light the

main burner.

2.

If the furnace does not come on when the
thermostat is set several degrees above room
temperature, set the thermostat to its lowest setting
to reset the safety control.

3.

Remove the burner access panel if provided on
your appliance.

4.

Push the on-off switch to the OFF
position.

5.

Wait five minutes to allow any gas in the
combustion chamber to vent. Then if you smell
gas, STOP! Follow Step 1 in the Warning above. If
you do not smell gas, continue with the next step.

6.

If you do not smell gas, push the electronic on-off
switch to the ON position.

7.

Replace the burner access panel.

8.

Reset the thermostat to the desired temperature.

9.

If the appliance does not turn on, turn the gas
control switch to OFF and contact a qualified
service technician for assistance.

Turning Off the Appliance

Vacation Shutdown

Set the thermostat to the desired room temperature while
you are away.

Complete Shutdown

1.

Turn off power to the appliance.

2.

Turn off the gas supply to the appliance.

3.

Push the on-off switch to the OFF
position. Appliance will completely shut off.

4.

Follow the procedure in the Instructions to the
Homeowner section above to resume normal
operation.

«
...
6
7
8

Содержание VR8215 Series









Отзывы:

Нет отзывов