Honeywell VP522A Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 8

Honeywell VP522A Скачать руководство пользователя страница 3

B SEQUENCING WATER VALVE

Nominal Body Rating:

250 psi (1724

Water Temperature Limits:

35F (2C) min to 250F (121 C) max

Packing:

Rubber V-ring, spring loaded, self adjusting

Seats:

Brass, upper seat removable, lower seat integral

Plugs:

Brass

Disc:

Molded-in composition

Operator Diaphragm:

Molded neoprene, rolling type

Operator Maximum Safe Air Pressure:

25 psi (172

Air Connections:

Combination barb fitting for

and

(4 mm

and 6 mm) 0. D. plastic tubing

MAINTENANCE

Equipment Required

Commercial cleaning solvent degreaser

0 to 30 psi (0 to 107

pressure gage

Cleaning

Remove all dirt and grease accumulation from the underside
of the actuator and around the packing nut and stem. Use
soivent if necessary.

A

WARNING

Use solvents in a well ventilated area. Avoid
prolonged inhalation of solvents or contact with the
skin. Careless handling of solvents can cause
permanent injury to the respiratory system and skin
tissue.

CAUTION

Do not allow solvent to come into contact with the
diaphragm as it will cause serious damage.

Adjust the system temperature controller through its
control range. The valve should operate to control the
flow of water as required to provide heating or cooling
(when both hot and chilled water are available).
Make sure the branchline pressure builds up to near full
main pressure when controller is set at the extreme end
of the throttling range. With the temperature controller

set at either extreme setting, full flow should occur.
There should be no flow at mid-pressure (see Table 1).

Adjustment

Make the following adjustments after repairing the
or

Vary the branchline pressure to the inlet port on the

Note the pressure range at which no

movement (dwell) occurs.
Repeat above procedure for the
Use a screwdriver or spring adjustment wrench to

adjust the tension of the spring on the

by

turning the spring clockwise to reduce, or counter-
clockwise to increase, the switching point of no
movement. The switching point must be within the

dwell.

Operational Check

If a gage is not already present, insert a 0 to 30 psi (0

to 107

gage in the branch line.

«
1
2
3
4
5
...
»

Содержание VP522A









Отзывы:

Нет отзывов