Honeywell V4043 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 9

Honeywell V4043 Скачать руководство пользователя страница 5

V4043, V4044 VALVES; V8043, V8044 ZONE VALVES

5

95-6983—11

Fig. 7. Remove old powerhead cover from systems using new style valve bodies.

4.

Install the new powerhead (see Fig. 6):
a. Place the manual opening lever (normally

closed models only) on the new powerhead in
the MAN. OPEN position.

b. Fit the powerhead onto the valve body, ensuring

that the shaft seats correctly. The powerhead
should be aligned so that the manual opening
lever or slot for lever is at the port A end of the
valve body.

c. Secure the powerhead to the valve body with

the two screws provided.

d. If fitted, reconnect the conduit or cable. Recon-

nect the leadwires to the powerhead.

e. Replace the powerhead cover.

5.

Turn on the power.

WIRING

Disconnect the power supply before connecting wiring to
prevent electrical shock or equipment damage.

All wiring must comply with local codes and ordinances.
Connections to the individual valves are shown in Fig. 8-
9. See Fig. 10 through 16 for typical hookups.

If replacing a Taco, Dole, Flair or White Rodgers 3-wire
valve with a 2-wire V8043E or F, see Fig. 17 through 29.
Check that the pressure rating of the new valve is
appropriate for the application.

Fig. 8. Typical wiring for V8043E, V8044E.

Fig. 9. Typical wiring for V8043F.

A

AUTO

MAN

OPEN

MANUAL
OPENING
LEVER

COVER
RETAINING
SCREW

M10161

A

B

B

V8043F 1036

24V 50/60 CY

.32 AMP

@ 60 CY

MADE IN CANADA

6

A

B

AUXILIARY
SWITCH

MOTOR

YELLOW
LEADS

TO CIRCULATOR
OR ANOTHER VALVE

RED LEADS

THERMOSTAT
(TYPICALLY T87F)

TO
LINE

M5953

R

L1
(HOT)
L2

1

1

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.

END SWITCH

TO CIRCULATOR
OR ANOTHER
VALVE

TH

TR

24V
TRANSFORMER

THERMOSTAT
(TYPICALLY T87F)

TH

TR

M5952

«
...
3
4
5
6
7
...
»

Содержание V4043










Отзывы:

Нет отзывов