Honeywell TWM 9000 Скачать руководство пользователя страница 34

Страница: 34 / 64

OPERATION

TWM 9000

www.honeywellprocess.com

34-VF-25-37 iss.2 GLO Jan 18 US

Time Stamp

The time when evaluation of the block was started and a

change in alarm/event state was detected that is unreported.

The time stamp value will be maintained constant until alert

confirmation has been received - even if another change of

state occurs.

Uninitialized

Setting:

MM / DD / YY (Month / Day / Year)

HH:MM:SS (Hour:Minute:Second)

Subcode

An enumeration specifying the cause of the alert to be

reported.

Other

Setting:

Other / Block Configuration / Link Configuration / Simulation

Active / Local Override / Device Fault State / Device

Maintenance / Input Failure / Output Failure / Memory

Failure / Lost Static Data / Lost NV Data / Readback Check /

Maintenance Needed / Power Up / Out Of Service

Value

The value of the associated parameter at the time the alert

was detected.

Setting:

0...255

CHANNEL

Channel

R/W

The number of the logical hardware channel that is connected

to this I/O block. This information defines the transducer to be

used going to or from the physical world.

Note:

W = Writeable only by setting "OOS" in MODE_BLK

Uninitialized

Setting:
1 (volume flow in m

/s)

2 (mass flow in kg/s)

3 (speed in m/s)

4 (coil temperature in

5 (conductivity in S/m)

6 (electronic temperature in

FIELD_VAL

Field Value

Raw value of the field device in percent of the PV range, with a

status reflecting the transducer condition, before signal

characterization (L_TYPE) or filtering (PV_FTIME).

Status

Actual Status is displayed.

Value

Actual Field Value

GRANT_DENY

Grant Deny

R/W

Options for controlling access of host computers and local

control panels to operating, tuning and alarm parameters of

the block.

GRANT

Grant

R/W

Depending on the philosophy of the plant, the operator or a

higher level device (HLD) or a local operator's panel (LOP) in

the case of "Local", may turn on an item of the "Grant"

attribute - "Program, Tune, Alarm or Local".

Uninitialized

Setting:

Program / Tune / Alarm / Local

DENY

Deny

R/W

The deny attribute is provided for use by a monitoring

application in an interface device and may not be changed by

an operator.

Uninitialized

Setting:

Program denied / Tune denied / Alarm denied / Local denied

HI_ALM

High Alarm

Mix

The status for High Alarm and its associated time stamp.

Settings of 5 subelements see in the following part.

Parameter

Parameter
Subelement

Access

Description and settings

Initial Value

Содержание TWM 9000

































































Результаты поиска

Содержание TWM 9000

Отзывы:

Похожие инструкции для TWM 9000

Бренды по названию

Популярные бренды

Honeywell TWM 9000, Дополнительное руководство по инструкции

Результаты поиска

Содержание TWM 9000

Отзывы:

Похожие инструкции для TWM 9000

Бренды по названию

Популярные бренды